SSD MEG102 Operation Manual Download

Page: 7 / 12

Setting Menu

F. Firmware Version : Display the meter's firmware vversion.
G. Temperture

: Sets the unit of measurement for temperture to either Farrenheit(°F)

or Celsius (°C)

H. Stabilization Mode : Sets the meter's clecrification period setting to either Auto and Fixed

Stabilization.

Auto - Enables a 15-second electrification period when the mersured

resistance is 1 x 10

Ohms or greater to maitain test accuracy.

Fixed - Complies with ANSI/ESD S4.1 and enables a 15-second

electrification period when the mearured resistance is 1 x 10

Ohms or greater.

I. Beep

: Enables and disables the sudible beep when the meter's pushbuttons

are pressed.

J. Erase all memory

: Erase all stored measurement transactions saved in the meter's

memory.

K. Memory Slot Number : Indicates the memory slot number.
L. Resistance Measurement : Indicates the resistance measurement value for the respsctive memory

slot

Summary of Contents for MEG102













Search results

Summary of Contents for MEG102

Reviews:

Related manuals for MEG102

Brands by name

Popular brands

SSD MEG102, Operation Manual

Search results

Summary of Contents for MEG102

Reviews:

Related manuals for MEG102

Brands by name

Popular brands