background image

12 

Bluetooth 

Bluetooth operation 

Connecting a mobile phone

 

To use the Bluetooth function, the following procedure is necessary 
 
1. 

Pairing 
When connecting Bluetooth devices for the first time, mutual registration is required. 
This is called “pairing”. This registration(pairing) is required only for the first time, as 
this unit and the other devices will recognize each other automatically the next time. 
(Depending on the device, you may need to input a pass code for each connection.) 
 

2. 

Connecting 
Sometimes pairing allows automatics connection. 
To use the device after pairing is made, start the connection. 
 

3. 

Hands-free talk/Music streaming 
You can call a mobile phone and listen to music when the connection is made. 

 

 

Some Bluetooth device may no support specific functions. 

-Devices are registered once paired and connected with this unit. You can select the 
registered device and connect it. 
-If pairing has already been archived, start operating from here. 
- Depending on the device, connection may start automatically after pairing. 
 

 

 

1. 

 Connect to this unit using your mobile phone or press 
Media/BT button 3 second or longer to show BT setting 
where you can select the desired device. 
 

Making a call via last call.

 

You can make a call from the connected mobile phone by operating this unit. 

 

 

1. 

Press and hold BT_ON button on Steering Wheel 
Controller(SWC) for more than three seconds to enter 
the last call dial mode. 
 
 

Pairing your phone and car audio system 

First, register(“pair”) a Bluetooth device (mobile phone, etc.) and this unit with each other. 
You can pair up to five devices. Once pairing is established, there is no need to pair again. 
Place the Bluetooth device with 3m(9ft) of this unit. 

Receiving a call 

When receiving a call, the ring tone is output from your car speakers and caller’s ID 
appears on screen.

 

 

 

1. 

Press and hold Media/BT button for more than three seconds. 
The unit enters pairing standby mode. 
The unit information, pass key and standby time will appears 
on the display. 

 

 

 
 
 
 
 

1. 

When a call comes in, “Incoming Call” and “Caller’s ID” 
appears with a ring tone, press  “BT_ON button on 
Steering Wheel Controller(SWC) or select “Accept” then 
press ENTER button. 
“Calling” with Call ID appears and the phone call starts. 
The built-in microphone of this audio system will pick up 
your voice. 
To receive the call on the mobile, select Secret and 
press ENTER. 
 
To reject an incoming call, rotate TUNE and select 
“Reject” and press ENTER button or press 
BT_Off/MUTE button on SWC. “CALL END” appears 
and return to previous function. 

 

 

2. 

Set the Bluetooth device to search for this unit. A list of detected devices appears in 
the display of the connecting device. This unit is displayed as “X100” on the 
connecting device. 
Confirm this by press “YES”, “OK” or “Pairing” on your mobile device. 
 

3. 

If  *Pass key input is required, input the “xxxx”(4 digit) number which is displayed on 
the this unit.  

 
4. 

Set the Bluetooth device to connected to this unit. 

 

Summary of Contents for SYMC X100 EA HU S014


















Reviews: