manualshive.com logo in svg

SRAM RockShox Super Deluxe Flight Attendant, User Manual, Page: 34 / 41

Share
Download
SRAM RockShox Super Deluxe Flight Attendant User Manual Download Page 34

34

Storage and Transportation

Storage conditions: Temperature from -40°C  to 70°C, humidity from 

10% to 85%
Operating conditions: Temperature from -10°C to 40°C, humidity from 

0% to 100%
Service life: 5 years

Remove the SRAM batteries and Pedal Sensor battery to preserve 

battery life during long term storage and when the bicycle is 

transported.
Remove the Pedal Sensor from the crank, and remove the AAA 

battery to preserve battery life.

NOTICE

Remove the SRAM batteries and install the battery blocks and battery covers when the bicycle is being transported or not in use for long 

periods of time. Failure to remove the SRAM batteries could result in battery depletion.
Failure to cover the battery and AXS component terminals could result in damage to the terminals.

Controller Battery Replacement

Use a coin to remove the battery cover.
Remove the battery from the cover.

NOTICE

To prevent moisture damage do not remove the battery cover o-ring seal.

1

2

3

Insert a new CR2032 coin cell battery 

into the battery cover, positive terminal 

side first.

Reinstall the battery cover. 
Use a coin to turn the cap clockwise to align the dots and lock it into place.

4

6

 

5

Install

Remove/Loosen

Adjust

Summary of Contents for RockShox Super Deluxe Flight Attendant










































Reviews:

No comments