SRAM DB-G2 RE-A2 Service Manual Download Page 36

Page: 36 / 39

Lever Brake Hose Installation

Insert the non-threaded end of a new compression fitting over the hose

barb and onto the brake hose and press the compression fitting onto

the hose until it stops.

the hose until it stops.
Thread the compression fitting onto the hose barb, counter-clockwise,

Thread the compression fitting onto the hose barb, counter-clockwise,

until it is flush or slightly lower than the hose barb.

The compression fitting is reverse threaded.

Slide the compression nut to the compression fitting.

Slide the compression nut to the compression fitting.
Apply DOT grease to the outside of the compression fitting and the

Apply DOT grease to the outside of the compression fitting and the

threads of the compression nut.

Insert the compression fitting into the lever and hold it firmly into the

lever. Thread the compression fitting into the lever by hand until it

stops.

DOT Grease

Summary of Contents for DB-G2 RE-A2








































Search results

Summary of Contents for DB-G2 RE-A2

Reviews:

Related manuals for DB-G2 RE-A2

Brands by name

Popular brands

SRAM DB-G2 RE-A2, Service Manual

Search results

Summary of Contents for DB-G2 RE-A2

Reviews:

Related manuals for DB-G2 RE-A2

Brands by name

Popular brands