SPYKER 30, Operation Manual Service Manual Parts List, Page: 6 / 8

SPEED - ACCURACY - FREEDOM FROM STRIPES AND STREAKS
are yours - when you use this Spreader.
The spread width ranges from 4 ft. to 12 ft. wide, depending on the volume/density,
particle size of the material and the rate of travel.
The spread thins or feathers at the outer edges, eliminating sharp, “Edge of spread”
lines which cause stripes and streaks. Extra coverage can be given under trees and
other heavy feeding areas without showing “edge of spread” lines.
Gaps and double overlaps are less likely. Small errors in travel are forgiven and do not
show.
WARNING: When spreading products containing herbicides, exercise extreme
caution with respect to careless spreading and to wind-drift.
CONTACT OF SOME PRODUCTS ON SOME PLANTS CAN BE FATAL.
If a dial setting is not found, use the size and weight comparison table found on the
back page.
Determine a dial setting on the low side. If the setting proves to be too low, cover the
area more than one time. A higher setting can be used when a proven dial setting is
established.
REMEMBER - Published dial settings can be approximate only. The operation of the
spreader, the condition of the material (damp or dry or over-pulverized) and weather
conditions, are all contributing factors.
For these reasons, it’s often a good idea to spread the area 2 times - at one-half rate -
in cross directions (SEE INFORMATION ON ONE-HALF RATE DIAL SETTINGS ON REFER-
ENCE CHART ON THE BACK PAGE. SPREADING AT ONE-HALF RATE DIAL SETTINGS IS
HIGHLY RECOMMENDED UNDER DAMP & HUMID CONDITIONS.
BECOME FAMILIAR WITH THE OPERATION OF THE SPREADER BEFORE YOU PUT
MATERIAL IN THE HOPPER.
Practice walking with the spreader, opening and closing the rate gate at the appropriate
times.
Travel at a constant speed and operate the spreader lever position.
Remember: Open the rate gate after the spreader is in motion at operating speed
(about 3 mph., or at a brisk walking pace).
Close the rate gate while spreader is still at operational speed.
Rotary Agitator
Use the rotary agitator only if needed. Free-flowing, lump-free materials will
not require the agitator. The rotary agitator is easily installed or removed.
Note the clockwise rotation & sweep. Place felt washer around spinner shaft
before inserting agitator. - See page #8.
OIL BEARINGS AND ALL MOVING PARTS
Make certain the spreader is running freely!
10
Item # Part # Quantity Description
1 SL-HP-1205 1 Hopper Only, 304 Stainless Steel
2 SS-90-0011 6 1/4 - 20 X 1 1/4” Bolt
3 SS-90-0012 3 1/4 - 20 X 1 1/2” Bolt
4 SS-91-0004 10 1/4 - 20 Lock Nut
5 SS-94-0007 1 Hopper Bottom Bearings
6 05-94-0068 1 Rate Gate
7 SS-94-0004 2 Rate Gate Guide
8 05-24-1101 1 Rate Gate Linkage
9 SS-94-0006 1 Dial Only
10 05-94-0069 1 Dial Mount
11 SS-94-0012 1 Spinner
12 SS-97-0004 1 Spinner Shaft
13 SS-96-0003 1 Rotary Agitator
14 SS-94-0009 1 Pinion Gear
15 SS-90-0001 2 1/8” x 3/4” Roll Pin/Pinion Gear/Bevel Gear
16 SS-90-0002 2 1/8” x 7/8” Roll Pin/Bevel Gear/Spinner
17 SS-97-0001 1 Axle
18 SS-90-0010 1 Drive Pin
19 SS-94-0010 1 Bevel Gear
20 SL-HP-1045 1 Gear Box with Bushing (Less Clamp Rings)
21 SS-94-0014 4 Clamp Rings Only
22 SL-HP-1004 1 Spinner Assembly/Axle, Gears, Gear Box, Spinner
23 SS-94-0011 2 Bushings for Axle at Frame
24 SS-95-0003 2 8” x 2.25” Super Duty Hard Rubber Wheel
25 SS-91-0001 2 Push Cap Nuts for Wheel Retention
26 SL-HP-1024 1 Painted Frame
27 SL-HP-1030 2 Support Brace Between Ground Prop & Frame
28 SS-92-0002 2 Felt Washer
29 05-94-0029 1 Bushing Only
30 05-24-1010 1 Top “T” Handle Section
31 SL-HP-1015 1 Center Handle Section
32 SL-HP-1120 1 Bottom Ground Prop Section
33 SS-94-0013 2 Handle Grips
34 05-98-0048 -1 1 On/Off Lever Control
35 05-91-0008 2 On/Off Lever Control Nut
36 05-90-0042 2 On/Off Lever Control Bolt
37 05-90-0044 1 Cable Fastener
38 05-24-1105 1 Cable Clamp
39 SS-90-0011 1 Cable Clamp Bolt
40 SS-91-0004 1 Cable Clamp Nut
41 SL-HP-1113 1 Rate Gate Assembly
42 05-90-0054 1 1/4 - 20 X 1-1/2” Hex Head/Frame/Ground Prop
05-99-0064 1 Manual
Model 54 Only
43 05-46-0500 1 Plastic Hopper
44 05-94-0065 1 Cover, Clear Plastic with Black
45 05-94-0064 3 Washer, Plastic
Model 34 Only
46 SS-97-0006 1 Axle 18 3/4” Long Drilled
47 SL-HP-1044 Axle, Gears, Gear Box, Spinner Assembly
48 99-50-1081 2 Axle, Cotter Pin
49 05-97-0008 1 Spinner Shaft 3/8 x 6 1/2
50 SS-95-0004 1 Pneumatic 8.5 x 3.5
51 05-24-1070 1 Hand Hold
Optional
52 05-82-0000 Extension Hopper
53 05-99-0021 Cover - Model 64 & 34
54 SL-EH-1005 Screen
55 05-94-0065 Cover - Model 54
Model 30 Only
56 05-54-0004 1 Spinner Shaft
57 05-300-0500 1 Hopper
Parts List
9
Spreader Assembly