background image

Visit

 

www.cuesinc.com

Global locations 

CUES (USA)

3600 Rio Vista Avenue, Orlando, FL 32805, USA 
Toll Free: +1 (800) 327 7791 [email protected]

CUES (Canada)

1675 Sismet Road, Mississauga, Ontario L4W 1P9, Canada 
Toll Free: +1 (877) 297 8957 [email protected]

Pearpoint (USA)

39-740 Garand Lane, Unit B, Palm Desert, CA 92211, USA 
Toll Free: +1 800 688 8094 Tel: +1 760 343 7350 [email protected]

As the world’s leading manufacturer of water, wastewater, and stormwater inspection 

equipment, CUES provides the necessary tools for both pipeline inspection and 

repair. For 50+ years, CUES has manufactured the most rugged and reliable pipeline 

inspection equipment in the industry.

Copyright © 2021 CUES Inc. All rights reserved 

CUES Inc is a subsidiary of SPX Corporation. This document may not be copied, reproduced, transmitted, or modified, in whole or in 

part, without the prior written consent of CUES Inc. Due to a policy of continued development, we reserve the right to alter or amend 

any published specification without notice.

Trademarks 

CUES (U.S. Trademark Reg. No. 4,843,936) and Accupoint are trademarks of CUES Inc. Radiodetection (U.S. Trademark Reg. 

No. 2,677,422), flexiprobe (U.S. Trademark Reg. No. 1,468,060), flexitrax (U.S. Trademark Reg. No. 5,467,647), and flexicoiler are 

trademarks of Radiodetection Ltd. Radiodetection Ltd is a subsidiary of SPX Corporation. Other trademarks or registered trademarks 

mentioned in this document belong to their respective owners.

Disclaimer 

Any references to third-party products (including hardware, software and services) in this manual are for informational purposes only 

and do not signify source, connection, sponsorship, affiliation, association, and/or approval with or by CUES Inc or SPX Corporation. 

CUES Inc expressly disclaims any liability for loss of data or damage to equipment resulting from or associated with third-party products.

Summary of Contents for CUES ACCUPOINT MS611

























Reviews: