Spudnik 290318, Manual

Page: 19 / 77

P
ARTS
M
ANUAL
4300 BULK BED
Part #: 290318
Revision: 4/18/2018
9
Section
-
2 Machine Overview
2.2. Label Identification and Part Number
Item # Qty Part # Description
1 4 300113 LABEL,CUIDADO,MAQUINARIA,OPERADA,POR
2 4 300101 LABEL,WARNING,POWER,DRIVEN,MACHINERY,CAN
3 3 300104 LABEL,WARNING,OPENING,DOOR,CAN,CAUSE
4 1 300131 LABEL,OPERATOR INSTRUCTIONS ENCLOSED
5 2 300003 LABEL,WARNING,KEEP GUARDS IN PLACE #659
6 1 300466 NOTICE:MODIFICATION MAY VOID WARRANTY
7 2 SEE PAGE 14 SEE PAGE 14
8 2 SEE PAGE 14 SEE PAGE 14
9 1 SEE PAGE 14 SEE PAGE 14
10 1 300055 SERIAL,NUMBER,PLATE 2"x3" ALUM W/HOLES
11 1 300175 DECAL,OIL,HYD,AW32
12 1 300042 LABEL,DANGER,240 VOLTS #500
12 1 300386 LABEL,DANGER,380 VOLTS #500
12 1 300041 LABEL,DANGER,480 VOLTS #500
12 1 300438 DECAL,DANGER 415 VOLTS
12 1 300452 LABEL,DANGER, 600 VOLTS
13 1 300910 TRUCK POWER,240V1P,PLUG
13 1 300911 TRUCK POWER,240V3P,PLUG
13 1 300912 TRUCK POWER,380V3P,PLUG
13 1 300913 TRUCK POWER,415V3P,PLUG
13 1 300914 TRUCK POWER,480V3P,PLUG
13 1 300915 TRUCK POWER,600V3P,PLUG
13 1 300916 TRUCK POWER,240V1P,CONNECTOR
13 1 300917 TRUCK POWER,240V3P,CONNECTOR
13 1 300918 TRUCK POWER,380V3P,CONNECTOR
13 1 300919 TRUCK POWER,415V3P,CONNECTOR
13 1 300920 TRUCK POWER,480V3P,CONNECTOR
13 1 300921 TRUCK POWER,600V3P,CONNECTOR
14 1 300959 LABEL,OPEN BALL VALVE BEFORE OPERATION
15 1 300957 LABEL,MOTOR ROTATION
16 1 SEE PAGE 14 SEE PAGE 14
17 1 SEE PAGE 14 SEE PAGE 14
18 1 SEE PAGE 14 SEE PAGE 14
19 1 SEE PAGE 14 SEE PAGE 14
1. Thoroughly clean and dry the area where the label is
to be installed.
2. Determine the exact label position before removing the
backing paper. Center the label so no edge will extend
beyond the flat surface to which it is being affixed.
3. Remove the smaller section of the backing paper.
4. While holding the exposed adhesive away from the
surface, rest the covered portion of the label on the
surface. Align the label in the chosen position.
5. Starting at the center, press the sticky portion of the
label to the machine surface. Press out any trapped air
bubbles as the label is applied.
2.3. Installing Replacement Labels
1. Use images on following pages to identify the location
for each of the labels used on the 4300 Bulk Bed.
2.4. Label Locations
6. Fold the label back to expose the remaining backing
paper. Peel the backing paper from the adhesive while
carefully pressing the label into position.
7. Small air bubbles can be deflated by piercing them with
a pin and pressing out the air using the slick side of the
backing paper.