background image

22

© SprayTECH.  All rights reserved.

Fluid Section Assembly

(Upright Cart P/N 0551675)

(Low Boy Cart P/N 0551676)

2 pt

2 pt

1

6

7

8

9

10

11

13

14

12

15

16

17

18

19

20

21

2

3

4

5

25

22

23

24

26

27

28

29

Install upper packing 

with raised lip 

facing down.

Raised Lip

Install lower packing 

with large beveled 

edge facing up.

Large Beveled Edge

Item

Part #

Description

Quantity

1

0508592

Retainer nut ................................................1

2

0508593

Piston guide ................................................1

3

0507273

Upper packing assembly ............................1

4

0551681

Pump manifold............................................1

5

0509873

Outlet fitting, 1/4” ........................................1

6

0507690

PRIME/SPRAY valve assembly .................1

7

0507274

Lower packing assembly ............................2

8

0551669

Piston rod....................................................1

9

0507734

Outlet valve seal .........................................1

10

0507945

Outlet valve cage........................................1

11

0507454

Washer, nylon .............................................1

12

9841502

Outlet valve ball ..........................................1

13

0294516

Outlet valve seat.........................................1

14

0507733

Outlet valve retainer ...................................1

15

0508598

Piston bushing ............................................1

16

0508599

Nylon washer ..............................................1

17

0507944

Inlet valve cage...........................................1

18

51519

Inlet valve ball.............................................1

19

00310

Inlet valve seat............................................1

20

0509582

O-ring, 

PTFE

..............................................1

21

0551661

Inlet valve housing, long tube (upright cart) ...1

0551662

Inlet valve housing, short tube (upright cart)

0551663

Inlet valve housing (low boy cart)

22

0508604

Filter seal ....................................................1

23

0508749

Filter support spring....................................1

24

0508603

Adapter .......................................................1

25

0508602

Filter spring .................................................1

26

0508748

Filter............................................................1

27

0508601

Filter housing ..............................................1

28

0551530

Return hose fittiing, 1/8” .............................1

29

0551678

Piston assembly (includes items 8–14) ......1

0551605

Filter assembly (includes items 22–27) ......1

0551677

Repacking kit (includes items 2, 3, 7, 9,
12, 16, 18, and 20)

0551511

Lower seal insertion tool

Summary of Contents for EPX2355

























Reviews: