background image

Profile LED Hyperion 300 TW

14

ADVANCED STROBE CHANNEL

valid in all the DMX modes where it is foreseen

Ch

Name

DMX Value

xx

ADVANCED 

STROBE

0

INACTIVE STROBE

1..150

Strobo from slow (3,86 s.) to fast 
(30 ms)

151..225 OFF

226..230

FULL WHITE
Enabling SERVICE control (set a 
parameter of the luminaire, and keep 
on hold for 5 secs.)
*In the DMX modes where the 
“SERVICE 2” - “LED CALIBRATION” 
is foreseen, if SERVICE is set on 
“LED CALIBRATION”, in this range 
the luminaire is on with calibration 
values set on channels 1..4

231..255 OFF

CCT CHANNEL

valid in all the DMX modes where it is foreseen

Ch

Name

DMX Value

xx

CCT

0..35

2700K

36..70 3000K

71..105 3200K

106..140 3500K
141..175 4000K
176..210 5600K

211..255 6500K

SERVICE FUNCTION
Service - Saving mode of a setup 
(EXCLUDING COLOUR CALIBRATION)

1. Select the setup you wish to perform through the 

SERVICE channel

2. Move the ADVANCED STROBE channel to the 

SERVICE area - the luminaire switches on at FULL 
WHITE

3. Keep on hold for 5 secs.
4. Three fl ashes confi rm that the operation was 

completed

SERVICE - COLOUR CALIBRATION saving mode

1. The colour calibration is available only for the dmx 

FULL 16bit mode

2. Set the fi rst 4 DMX channels on the desired 

calibration values WW1, WW2, CW1, CW2

3. Select the COLOUR CALIBRATION range (192..197) on 

the SERVICE channel

4. Move the ADVANCED STROBE channel in the SERVICE 

range (231..240); the luminaire switches on at the 
calibration values set on channels 1..4

5. Keep on hold for 5 secs.
6. Three fl ashes confi rm that the operation was 

completed.

When the dmx channel SERVICE is in the COLOUR 
CALIBRATION area and the dmx ADVANCED STROBE 
channel is in the SERVICE range the luminaire switches 
on at the calibration values set in channels 1..4: during 
this phase it is possible to adjust these calibration values; 
it will be then enough to move the dmx ADVANCED 
STROBE channel out of the SERVICE 2 value range, and 
then take it back to that range and wait for 5 seconds to 
have the calibration values saved. The operation will be 
confi rmed by three fl ashes of the luminaire.

Summary of Contents for Fresnel LED Hyperion 300 TW

















Reviews: