SportsArt Fitness T615 Repair Manual Download | Manualshive

Page: 46 / 48

background image

4-6-1

Inspection and Measurement

Model : T615

            Inspection point:    Measuring VR voltage on the drive board
            Inspection method:    1. Select the VDC setting on the multi-meter. Place probes on the VR set red-green wires.
                                                  2. If the VR voltage fluctuates widely, the VR is bad. Replace it.

Incline key

Drive board VR voltage

Incline position

0%

Red-green 1.20V

At red line (calibration point)

15%

Red-green 3.57V

Longest position

measure
Incline VR voltage
red-green
0%

1.20V

15%

3.57V

Incline red line

«
...
44
45
46
47
48
»

Summary of Contents for T615

















































Reviews:

No comments

Related manuals for T615

Brand: Pro-Form Pages: 28

Brand: Zipro Pages: 157

PRO-FORM PREMIER 1300

Brand: ICON Health & Fitness Pages: 40

Brand: Weslo Pages: 16

Brand: LSG Pages: 32

Brand: LifeSpan Pages: 28

Brand: Northern Lights Pages: 38

Brand: NordicTrack Pages: 32

Brand: CYBEX Pages: 70

Brand: Robotouch Pages: 7

Brand: Landice Pages: 20

Brand: Orbit Pages: 19

Brand: LifeGear Pages: 17

Brand: Weslo Pages: 24

Brand: Weslo Pages: 24

Cadence C72 Treadmill

Brand: Weslo Pages: 30

Brand: Freemotion Pages: 36

Brand: ProForm Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands