19
www.spokey.eu
www.spokey.pl
SETTING THE SPEED
When running on the treadmill, the speed can be adjusted by moving
at sliding block..
Speed adjustment range: 0-15km/h
SAFETY KEY
A safety key is intended to deactivate the treadmill immediately if you fall
down. It serves as an emergency stop. The safety key must be used in
urgent cases only.
For safe and convenient stop, use START/STOP button until the treadmill
stops completely. Once you have pressed START/STOP, the treadmill belt
will gradually decreased its speed. The treadmill will not activate until you
have inserted the safety key in the key hole located in the centre of the
counter control desk, which provides additional protection to treadmill
activation by third parties. The other end of the key must be attached to
clothes. If you fall down, the safety key will fall out the control desk and the
treadmill will stop immediately. Use only in urgent situations
ACTIVATION
Connect the plug to the socket, the counter display turns on and the track
goes into standby mode.
SLEEP MODE
After 10 minutes of inactivity, the track goes into sleep mode and the
counter is turned off. Press any button to resume the track.
BUTTON FUNCTIONS
START/STOP
press to start the training or a chosen programme. 3
seconds after the start, the running belt will start moving at the lowest
possible speed or at the speed corresponding to a chosen programme.
Press to stop the training. The treadmill will be slowing down until it stops
completely.
DISPLAY INFORMATION
SPEED:
current speed.
DIS, TIME, CAL.:
the screen displays the value marked with a glowing
diode: distance ran, workout time, number of calories burnt during the
current training session.
SMART MODE (P. 4)
1) Level mode
Total 8 levels, they are more and more difficult, users need to pass the
previous level, then can enter the next level.
2) Aerobic running
“Aerobic running "is a kind of low intensity running style, total 8 kinds of
programs.
Click to enter one program, the histogram means different speed, white
histogram represents finished running segment, the red histogram
represents current running segment, the blue histogram represents not
finished segments. The system defaults to 3 minutes for a segment, the
user can adjust speed during the running.
3) Slim running
"Slim running" is a kind of medium intensity running style, total 12 kinds of
programs.
4) High strength running
"High strength running" requires users to have a certain running speed and
skills, not suitable for beginners. Total 12 kinds of programs.
5) Customized mode
The user can set the running time, speed, according to the personal hobby,
the program can be included several segments.
6) Target setting mode
The user can set target time, distance and calorie, then click "START" to
run, after target finished, the treadmill automatically stops.
SCENE MODE (P. 5)
The user can choose any scene they like, then click “START”,feeling like
running in that scene.
USER (P. 6)
1. Press the "User" button at home page to enter the user's interface. The
system has a default "guest" , you can modify the default information and
can also add personal account.
A) Edit user information
Click "User Edit" to modify current user information
Add new user
Click the button to add new user and edit the new user information.
B) User login
Click the button to enter the user login interface. Select the
automatic login, then next time will automatically login on the
account. Or select "remember password", no need to enter
the password again.
TROUBLESHOOTING
Failure phenomenon
Possible Cause
Approach
Electronic Table no
display
1, the signal wire connection is poor or broken
2, not plug well
3, overload protection action
4, the transformer burned
1, re-connect signal wire or change new wire
2, re-plugged the power cord
3, reset overload protection
4, change new transformer
Motor does not run
1, the safety key not put on
2, the electrical power cord is not connected
3, the PCB signal wire is not well connected
4, PCB damage
5, motor damage
1, put on the safety lock
2, re-plugged the power cord
3, re-connect signal line
4, change new PCB
5, change new motor
Show E01
1, the signal cable is not well connected
2, the signal wire damage
1, re-connect signal wire
2,change new signal wire
Show E02
1, Explosion-proof protection
2, PCB burnt
3, Motor wire not well connected
1,Check input voltage
2,Chang new PCB
3,Re-connect motor wire
Summary of Contents for 926731
