18
www.spokey.eu
www.spokey.pl
ATTENTION: Before transporting the treadmill make sure that it is
disconnected from power supply. The device should always be transported
by two persons..
MAINTANCE
Caution: before cleaning / lubrication you must take out the power plug from
a socket.
For cleaning the exercise machine, do not use any abrasive detergents.
Use a soft, damp cloth to remove dirt and dust.
The monitor should be cleaned only with a dry cloth.
The equipment should be stored in dry places in order to protect it from any
moisture and corrosion.
Use a soft, damp cloth to wipe off the edges of the treadmill belt, and the
space between the treadmill belt and the frame edges. Clean the edge of
the belt on its bottom side also. Clean the upper part of the belt with a brush
and soap water once a month.
NOTE: Before you start using the treadmill again, wait until the equipment
is completely dry.
Vacuum under the equipment at least once a month to prevent dust from
accumulating.
Once a year, it is recommended to remove the cover of the engine in order
to remove any dust that may accumulate there.
NOTE: The level of equipment operational safety can be maintained only
by regular inspections checking for any damage and wear.
Connecting elements are the most vulnerable to any wear..
BELT TENSION ADJUSTMENT
Belt Tension Adjustment-It is very important for joggers and runners in
order to provide a smooth, steady running surface. Adjustment must be
made from the right and left rear roller in order to adjust tension with the
Hexagonal Wrench provided in the parts package. The adjustment bolt is
located at the end of the rails as noted in diagram below.
Note: Adjustment is thru the small holes on the end caps.
Tighten the rear roller only enough to prevent slippage at the front roller.
Turn both the right and left bolt clockwise reasonably and inspect for proper
tension. When an adjustment is made to the belt tension, you must also
make a tracking adjustment to compensate for the change in belt tension.
DO NOT OVERTIGHTEN - Over tightening will cause belt damage and
premature bearing failure.
BELT TRACKING ADJUSTMENT (PICTURE, P. 9)
This treadmill is designed to keep the belt reasonably centred while in use.
It is normal for some belts to drift near one side while the belt is running
with no one on it. After a few minutes of use, the belt should have a
tendency to centre itself. If during use, the belt continues to move toward
one side, adjustments are necessary. The procedures are as below:
▲ First set speed at lowest position.
▲ Second check the belt shifts to which side.
If the belt shifts to right, tighten the right bolt and loosen the left bolt by
using 6mm Hexagonal Wrench, until the belt is centered itself; if belt shifts
to left, tighten the left bolt and loosen the right bolt by using 6mm Hexagonal
Wrench, until the belt is centered. When adjusting the belt using the 6 mm
Hexagonal Wrenches, it is important to adjust the belt in half turn
increments. Over adjusting the belt can cause damage to the mat.
HOW TO CHECK THE RUNNING MAT FOR PROPER LUBRICATION (PICTURE, P. 9)
Disconnect the main power supply.
Fold the treadmill up into the storage position.
Feel the back surface of the running mat.
BELT/DECK/ROLLER LUBRICATION
The mat/deck friction may play a major role in the function and life of your
treadmill and that is why we recommend you constantly lubricate this
friction point to prolong the life time of your treadmill.
You should apply the lubrication after approximately the first 20 hours of
operation. We recommend lubrication of the deck every 30 days.
See below procedures for lubricating:
Use a soft, dry cloth to wipe the area between the belt and deck.
Spread lubricant onto the inside surface of belt and deck evenly (make sure
the machine is turned off and power is disconnected).
Periodically lubricate the front and rear rollers to keep them at their peak
performance.
If the treadmill belt/deck/roller is kept reasonably clean it is possible to
expect over 100 hours before additional re-lubing is necessary
HOME PAGE (P.3)
displays the following features:
A) Scene mode: click to enter the scene mode
B) Smart model: click to enter the smart mode
C) Start: click to start treadmill, you can adjust speed according to your
hobby.
SECOND PAGE (P.3)
It has many pre-
setting Apps, but can’t install App by yourself because the
system space is limited.
Click on the upper left corner, you can return to the home page.
A) Data
Click “Data” to enter ,this interface can show daily running data,
or the daily running data in each month.
Noted: due to the treadmill system time from the network server time. In
order to accurately display the data , please connect Wifi before running.
B) Setting
WIFI connecting
Click”Settings” to enter interface, select system setting, will appear Wifi
signal, click it and connect Wifi.
STARTING AND ENDING WORKOUT
1) Start treadmill
From the first page of the home page, click "START" button to enter the
running interface.
2) Stop treadmill
click "STOP" button
Click on the upper left corner , you can return to home
page. At the home page, the original "start" will be
displayed as "Running
”.
TREADMILL BELT
MULTIMEDIA DISPLAYBASIC INFORMATION
Summary of Contents for 926731
