Performer s1200 – Quickstart
Performer s1200 – Quickstart
2
3
AVIS: RISQUE DE CHOC ÉLECTRIQUE • NE PAS OUVRIR
RISK OF ELECTRIC SHOCK
D O N O T O P E N
C A U T I O N
1. Remove Fuse Holder
2. Exchange Fuses
3. Flip Over
4. Reinstall
spl.audio
Pin 1 = GND
Pin 2 = Hot (+)
Pin 3 = Cold (–)
~ 115V AC / ~230V AC, 50 Hz / 60 Hz,
P max. 1375 VA
TRIM
TRIM
AM
P CTL/
12V T
RIG
GER
Connect to
SPL devices
supporting
AMP CTL
for remote
standby on/off.
Made in Germany
+
+
–
R
R
2
ώ
2
ώ
L
L
–
Serial
Number
Performer s1200
Stereo Power Amplifier
AMP CTL/12V TRIGGER
VO
LTA
GE S
ELEC
TIO
N
VOLTAGE SELECTION
230V AC:
T 6.3 A
L 250 V
115V AC:
T 10 A
L 250 V
FUS
E
FUSE
SPEAKER OUT
PUT LEFT
XLR WIRING
XLR WIRING
SPEAKER OUTPUT LEFT
INPUT LEFT
INPUT SELECT
INP
UT L
EFT
INP
UT S
ELE
CT
INPUT RIGHT
INPU
T RIGH
T
Sound Performance Lab
SPEAKER OUTPUT RIGHT
Minimum Load
Minimum Load
SPEAKER OUT
PUT RIGHT
• •
•
•
•
•
•
•
•
•
•
•
0
-5
.5
-5
-4
.5
-4 -3.5
-3
-2
.5
-
2
-1.5
-1
-0
.5
• •
•
•
•
•
•
•
•
•
•
•
0
-5
.5
-5
-4
.5
-4 -3.5
-3
-2
.5
-
2
-1.5
-1
-0
.5
RCA
XLR
EN
DE
Speaker Output R
AMP CTL
Input R
Input L
Mains Voltage
Mains Switch
Speaker Output L
Mains Connector
14
9
9
7
8
8
3
4 11
5
Gain Trim R
Gain Trim L
Input Switch
15
15
16
Start up
Read the security advices on page 6!
Remove the two transport locking screws at the bottom of the Performer s1200.
Keep the transport locking screws safe. For transport screw the transport locking screws back in.
Make sure that the selected mains voltage of the Performer s1200 is according
to the mains voltage of your region.
Make sure that the mains switch on the rear of the Performer s1200 is set to Off
(Off = O / ON = I).
Connect the supplied power cord to the Performer s1200 and an appropriate
mains socket outlet.
If the supplied power cord does not match your mains socket outlet, please contact your dealer.
Turn off all devices you wish to connect to the Performer s1200.
If you own an SPL device supporting AMP CTL output(s) you can trigger standby
and operation. Therefore connect the AMP CTL output of the SPL device with a
mono mini jack cable to the AMP CTL input of the Performer s1200.
Mono mini jack cable is not included in the scope of delivery.
You may also use other 12V trigger controller. The Performer s1200 is in opera-
tion mode when a switching voltage of 12 Volt DC is applied to the AMP/CTL
input.
As soon as the 12 Volt DC is removed, the Performer s1200 switches back to
standby mode.
Use a mono mini jack cable where the tip is plus and the sleeve is minus.
Connect the outputs of your preamplifier to the inputs (INPUT) of the
Performer s1200. Please use appropriate audio cables (XLR or RCA).
Audio cables are not included in the scope of delivery.
Connect the Performer s1200 with speaker cables to your speakers.
Speaker cables are not included in the scope of delivery.
1
2
3
4
5
6
7
Tip
Sleeve
8
9
