background image

4

Please note and retain this manual. Carefully read and follow all of the safety 

and operating instructions before you use the machine. 

Be  doubly  careful  to  follow  all  warnings  and  special  safety  instructions 

noted in this manual and on the unit. 

Connections: 

Only use the connections as described. Other connections can 

lead to health risks and equipment damage.

Water And Humidity:

 Do NOT use this machine anywhere near water (for 

example near a wash basin or bath, in a damp cellar, near swimming pools, 
or the like). In such cases there is an extremely high risk of fatal electrical 
shocks!

Insertion Of Foreign Objects Or Fluids: 

NEVER allow a foreign object through 

any of the machine‘s chassis openings. You can easily come into contact with 
dangerous voltage or cause a damaging short circuit. NEVER allow any fluids 
to be spilled or sprayed on the machine. Such actions can lead to dangerous 
electrical shocks or fire! 

Opening the Machine:

 Do NOT open the machine housing, as there is great 

risk you will damage the machine, or – even after being disconnected – you 
may receive a dangerous electrical shock!

Electrical Power:

 Run this machine ONLY from sources which can provide 

proper power at the prescribed rating. When in doubt about a source, contact 
your  dealer  or  a  professional  electrician.  To  be  sure  you  have  isolated  the 
machine, do so by disconnecting the power cord from your wall connection. 
Be sure that the power cord plug is always accessible. When not using the 
machine  for  a  longer  period,  make  sure  to  unplug  it  from  your  wall  power 
socket. 

Power Cord Protection:

 Make sure that your power cord is arranged to avoid 

being stepped on or any kind of crimping and damage related to such event. 
Do not allow any equipment or furniture to crimp this power cord.

Power Connection Overloads: 

Avoid any kind of overload in connections to 

wall  sockets,  extension  or  splitter  power  cords.  Always  keep  manufacturer 
warnings and instructions in mind. Overloads create fire hazards and risk of 
dangerous shocks!

Lightning: 

Before thunderstorms or other severe weather, disconnect the 

machine from wall power (but to avoid life threatening lightning strikes, not 
during  a  storm).  Similarly,  before  any  severe  weather,  disconnect  ALL  the 
power connections of other machines and antenna and phone/network cables 
which may be interconnected so that no lightning damage or overload results 
from such secondary connections.

Important Security Information

Summary of Contents for Kultube 2049

























Reviews: