Spitwater SHW68 Original Instructions Manual Download | Manualshive

Page: 13 / 23

background image

13

10. NOZZLE ASSEMBLY

Connect the high pressure nozzle (smaller hole) and the low pressure nozzle (larger hole) to the lance. Do
not over tighten and make sure that the nozzle positions do not interchange during assembly. Add nozzle
shield after nozzle assembly. Refer diagram below.

11. LANCE, TRIGGER GUN & HIGH PRESSURE HOSE ASSEMBLY



Connect the lance to the spray gun by an in-built quick release coupling.



Connect the high pressure hose fitting to the spray gun. Do not over tighten.



Connect the quick release adaptor to the high pressure hose fitting. Do not over tighten.

«
...
11
12
13
14
15
...
»

Summary of Contents for SHW68
























Reviews:

No comments

Related manuals for SHW68

Brand: Favor.it Pages: 9

Martha Stewart MTS-1450PW

Brand: SNOWJOE Pages: 16

Brand: Heinner Pages: 86

INDEPENDENT 1900

Brand: Lavor Pages: 108

Brand: Michelin Pages: 40

Brand: GEAppliances Pages: 16

Brand: Kärcher Pages: 98

Brand: Kärcher Pages: 232

Brand: Kärcher Pages: 22

Brand: MAKINEX Pages: 58

Brand: Indesit Pages: 16

Brand: Maytag Pages: 52

Brand: IPC Pages: 104

Brand: Kogan Pages: 19

Brand: CORBERO Pages: 13

Brand: Briggs & Stratton Pages: 16

Brand: Simoniz Pages: 18

Brand: Wen Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands