Spirax Sarco TD120 Installation And Maintenance Instructions Manual Download Page 6

Page: 6 / 12

IM-P150-07

ST Issue 4

�

��

�

��

�

��

Pressure bar g

Temperature

Steam

saturation

curve

The product

must not

be used in this region.

A - B

Socket weld and butt weld ends.

A - C

Flanged to DIN 2549 PN250.

A - D

Flanged to ANSI 1500.

A - E

Flanged to DIN 2548 PN160.

A - F

Flanged to ANSI 900.

A - G

Flanged to ANSI 600 and DIN 2547 PN100.

2.3 Pressure/temperature limits

(ISO 6552)

Body design conditions

PN250

PMA Maximum allowable pressure

250 bar g @ 522

C (3 626 psi g @ 972

TMA Maximum allowable temperature

550

C @ 153 bar g (1 022

F @ 2 220 psi g)

Minimum allowable temperature

-29

(-20

PMO Maximum operating pressure

250 bar g

(3 626 psi g)

for saturated steam service

TMO Maximum operating temperature

550

C @ 153 bar g (1 022

F @ 2 220 psi g)

Minimum operating temperature

(32

Note:

For lower operating temperatures consult Spirax Sarco.

PMOB Maximum operating backpressure should not exceed 50% of the upstream pressure
Minimum operating differential pressure

8 bar g

(116 psi g)

Designed for a maximum cold hydraulic test pressure of

375 bar g

(5 439 psi g)

Pressure psi g

Temperature

Summary of Contents for TD120













Search results

Summary of Contents for TD120

Reviews:

Spirax Sarco TD120, Installation And Maintenance Instructions Manual, Page: 6 / 12

Search results

Summary of Contents for TD120

Reviews: