background image

©2015 Mad Dogg Athletics, Inc. All rights reserved. Spin®, Spinner®, Spinning®, Spin Fitness® and the Spinning logo  ® are 

registered trademarks that are owned by Mad Dogg Athletics, Inc.

18

COMPUTER CARE

Spinning® strongly recommends performing regular maintenance to ensure 
the computer is working at its best for years to come. The recommended 
maintenance procedures are listed below:

Daily:

• 

Wipe down the computer with a soft cloth after each use. 

• 

Dilute a non-toxic cleaner like Simple Green® with water in a 30:1 
water-to-cleaner ratio. Spray the solution onto a soft cloth, then 
wipe the computer console.

• 

Never spray directly onto the computer console. Never use 
abrasive cloths or oil, ammonia or alcohol-based cleaners.

Weekly:

• 

Inspect each console for loose parts, bolts and nuts. Adjust and 
tighten loose points as needed.

• 

Remove any consoles that are not properly mounted or at risk of 
coming loose.

Monthly:

• 

Inspect all areas for proper adjustments.

• 

Inspect all parts for damage which could require possible 
replacement.

• 

Inspect mounting of the cadence sensor and magnet to ensure it is 
intact and working properly.

• 

A “low battery” indicator will display when batteries need 
replacing. Replace the batteries in the console with 3 high-quality 
AAA alkaline batteries from brands like Panasonic®, Duracell® and 
Energizer®.

Summary of Contents for STUDIO COMPUTER

























Reviews: