background image

9.

 

Limited

 

Warranty

 

 

JDC

 

ELECTRONIC

 

SA

 

extends

 

a

 

12

 

months’

 

warranty

 

over

 

parts

 

and

 

labour

 

for

 

this

 

instrument,

 

effective

 

from

 

the

 

date

 

of

 

purchase.

 

JDC

 

ELECTRONIC

 

SA

 

reserves

 

the

 

right

 

to

 

repair

 

or

 

replace

 

any

 

component

 

which

 

may

 

have

 

become

 

faulty

 

in

 

the

 

course

 

of

 

normal

 

use.

 

This

 

repair

 

or

 

replacement

 

shall

 

be

 

carried

 

out

 

at

 

no

 

charge

 

to

 

the

 

customer

 

(parts

 

or

 

labour).

 

Transport

 

costs

 

however

 

shall

 

be

 

borne

 

by

 

the

 

customer.

 

This

 

warranty

 

does

 

not

 

cover

 

damages

 

caused

 

by

 

an

 

accident,

 

abnormal

 

or

 

excessive

 

use,

 

or

 

resulting

 

from

 

an

 

unauthorised

 

modification

 

or

 

repair.

 

 

For

 

international

 

warranty

 

support,

 

please

 

contact

 

your

 

dealer.

 

 
 

 

 

Developed

 

and

 

manufactured

 

by:

 

JDC

 

ELECTRONIC

 

SA

 

Rue

 

des

 

Uttins

 

40,

 

1400

 

Yverdon

les

Bains,

  

Switzerland

 

Phone:

 

++41

 

(24)

 

445

 

2121

  

Fax:

 

++41

 

(24)

 

445

 

2123

  

e

mail:

 

[email protected]

 

Internet:

 

http://www.jdc.ch

 

NTech USA

 

PO Box 284, Holmen, WI 54636

USA
Phone: 608.498.4021
Fax:      608.531.2608 

e-mail: info@

ntech

usa.com

Internet: www.

ntech

usa.com 

 

Summary of Contents for Wireless Speed Computer

















Reviews: