SPEED FREAK PANTERA Assembly Manual Download Page 14 | Manualshive

Page: 14 / 24

background image

14

13. Mount the Castle Creations Talon 90 ESC to the bottom of the motor box
with nylon zip ties or a Velcro strap. I like to place a piece of dense foam
under the ESC to dampen any vibration. Insert the bullet connectors into the
receptacles on the ESC.

14.  Assemble the provided balsa baffles and install them on the sides of the
motor box as shown with medium CA.  You may have to trim the baffles
slightly for proper fit.  DO NOT OMIT THIS STEP!  We will be pushing this
power system hard and need to provide adequate ducting for cooling air to
reach the motor as well as for the heated air to exit.

«
...
12
13
14
15
16
...
»

Summary of Contents for PANTERA

























Reviews:

No comments

Related manuals for PANTERA

Brand: L. G. B. Pages: 4

Brand: Radio Flyer Pages: 6

Brand: Laser Pegs Pages: 3

Brand: Park Pilots Pages: 12

68in SLICK540 20CC

Brand: Goldwing RC Pages: 32

Brand: Fisher-Price Pages: 2

Little Helper’s Cart & Shopping Set 4862

Brand: Step2 Pages: 4

Brand: Multiplex Pages: 36

My Little Baby Born I Can Swim!

Brand: Zapf Creation Pages: 4

Brand: Vollmer Pages: 12

Brand: Fisher-Price Pages: 2

Lightning McQueen Learning Laptop

Brand: VTech Pages: 10

Brand: E-FLITE Pages: 20

Kawasaki Adventure 4x4

Brand: Power Wheels Pages: 28

Brand: X-PRO Pages: 32

Brand: WATT AGE Pages: 36

2-in-1 Journey Wagon 3379

Brand: Radio Flyer Pages: 2

Clone Trooper Junior Laptop

Brand: Oregon Scientific Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands