manualshive.com logo in svg

SPEED FREAK PANTERA, Assembly Manual

Share
Download
SPEED FREAK PANTERA Assembly Manual Download Page 2

2 

 

Greetings and congratulations on your purchase of the SPEED FREAK 
PANTERA!  The PANTERA is the second release from SPEED FREAK and 
is built around the Xpwr T3520, the same motor that powers the Outlaw to 
ballistic speeds! 

The Pantera is rock solid and tracks like a pattern plane.  It is capable of 
performing graceful big sky aerobatics and is very easy to fly and land.  It is 
NOT a model for performing 3D aerobatics and has been designed with small 
control surfaces to minimize the potential for flutter during maximum speed 
flight.  Close attention must be paid during linkage setup to maximize 
mechanical advantage and minimize throws.  Sealing the control surface gaps 
is a must!  We are pushing the airframe, power system and guidance 
components hard and must make sure they are properly utilized and looked 
after to achieve and maintain maximum performance.  Please pay close 
attention to the steps in this assembly manual, especially those steps regarding 
linkage and power system setup. 

 

The Ultracote/Oracover color used on these models are as follows: 

Red/White/Blue scheme-Midnight Blue HANU885 (Oracover Dark Blue #52), 
True Red HANU866 (Oracover Ferrari Red #23), White HANU870 (Oracover 
White #10), Black HANU874 (Oracover Black #71) and Silver HANU881 
(Oracover Silver #91) 

Blue/Yellow scheme-Midnight Blue HANU885 (Oracover Dark Blue #52), 
Bright Yellow HANU872 (Oracover Cadmium Yellow #33).

 

 

 

 

 

 

Summary of Contents for PANTERA

























Reviews:

No comments

Brands by name

Popular brands

Load more brands