manualshive.com logo in svg

Spectrum Techniques ICS-PCI, User Manual

Share
Download
Spectrum Techniques ICS-PCI User Manual Download Page 6

 

6 

Installation 

 

Before installing a ICS-PCI Card for the first time, the 

software should be installed

. 

 

Your ICS-PCI card has been factory configured to operate internally in most IBM ® compatible PC's. System 

requirements; 486 or Pentium processor, 8 meg RAM, 640 x 480 VGA or SVGA graphics, Microsoft Windows® version 98 

or higher, compatible mouse, and an available PCI slot. The software requires 3.0 meg available disk space. If problems 

occur and the ICS-PCI card does not respond correctly to the software commands, refer to the 

Technical Reference

 

section of this help file. If problem persists, contact the factory. 

 

The ICS-PCI software is defaulted to enable the internal amplifier on the card. This configuration requires the use of a 

simple high voltage divider type photomultiplier tube base. The signal (anode) from the base may be connected directly to 

the ICS-PCI bottom Input (BNC) connector and the HV (high voltage) connected directly to the top HV (MHV) connector. 

 

The BNC and MHV connectors have a similar appearance, exercise care when making these connections. 

 

  

 

 

Software Installation 

 

Place ICS-PCI software disk into the appropriate disk drive on the computer that will be using the ICS-PCI card. 

 

Using the Windows Explorer, locate the drive and folder containing the ICS-PCI Software. Launch the Setup program by  

double-clicking the Setup program icon. Continue to follow the instructions on the screen. In most cases, the default  

responses will be adequate. 

  

 

Card Installation 

 

The intended computer for use of the ICS-PCI card must have at least one available PCI slot.  

 

Remove the case cover and install the ICS-PCI circuit card into the PCI bus of the computer.  

Ensure that the card is seated firmly into the slot. Secure the card to the chassis of the computer with screw. 

 

After the card has been installed, connect the detector signal to the card BNC connection and the high voltage  

MHV to the detector HV connection. If the optional temperature sensor has been purchased, connect it to the  

T/COMP connector.   

 

 

WARNING - DO NOT connect a telephone to the T/COMP connection. It is not compatible with modem or network 

devices. Connection of unsupported devices to any of the connections may damage the ICS-PCI card or the external 

device and could result in a voided warranty. 

Summary of Contents for ICS-PCI












































Reviews:

No comments

Brands by name

Popular brands

Load more brands