Spectrex SharpEye 40/40C Series Reference Manual Download | Manualshive

Page: 21 / 50

background image

4. Close the terminal compartment by screwing the back cover on to the housing.
5. Tighten the back cover security screw.

Figure 2-11: Closing security screw

A. Back cover security screw

B. Ground cable connection point

6. Connect the ground cable.

WARNING

The terminal temperature may be higher than 185 °F (85 °C).

CAUTION

To comply with EMC directive 2014/30/EU and protect against interference caused
by radio frequency interference (RFI) and electromagnetic interference (EMI), shield
the cable to the detector and ground the detector. Ground the shield at the
detector end.

2.6

Install the protective cover

CAUTION

Always install the protective cover with the detector.

The protective cover is available in ABS plastic or stainless steel.

Table 2-3: Protective cover

Material

Part number

ABS plastic

00975-9000-0020

Stainless steel

00975-9000-0021

Reference Manual

Installation

00909-0100-4975

December 2021

SharpEye 40/40

21

«
...
19
20
21
22
23
...
»

Summary of Contents for SharpEye 40/40C Series



















































Reviews:

No comments

Related manuals for SharpEye 40/40C Series

Brand: Faraday Pages: 2

Brand: dallmeier Pages: 2

Brand: NAPCO Pages: 80

Smart Home Monitoring

Brand: Rogers Pages: 20

Brand: Response Alarms Pages: 16

SAPPHIRE COMPACT 309150001

Brand: Hygood Pages: 6

Brand: CAMERA LINK Pages: 36

Brand: 3xLogic Pages: 16

iDS-2CD6124FWD-B

Brand: HIKVISION Pages: 29

Brand: Amico Pages: 4

Brand: ESP Pages: 4

Brand: Velleman Pages: 58

Brand: ICP DAS USA Pages: 96

Brand: Dante Pages: 40

Brand: COHU Pages: 21

Brand: M2M Pages: 7

Brand: Velleman Pages: 16

Brand: Abus Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands