SpectraPure Coffee Lovers System CLS-5-90 Operation Manual Download

Page: 10 / 24

SpectraPure

SpectraPure®Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

FAUCET INSTALLATION

Figure 3

AIR-GAP FAUCET PARTS LIST

Faucet

- Galvanized Flange

- Rubber Washer

- Flat Metal Washer with “U” Cutout

- Plastic Spacer with Cutout

- Flat Metal Washer

- Hex Nut

- 1/4” Quick Connect Plastic Tubing Adapter

AIR-GAP FAUCET INSTALLATION

A. Place the chrome counter plate and rubber washer over the threaded shaft and barbed

nipples on the faucet (Refer to Figure 3).

B. Pass the Blue 3/8” tubing, the Yellow 1/4” tubing, and the Black 3/8” tubing up through the drilled

counter-top hole and temporarily secure them so they don’t fall back through the hole.

C. Place the galvanized flange, plastic spacer, flat metal washer, and hex nut in sequence over the threaded

shaft and temporarily hand-tighten, then screw the push fitting onto the end of the threaded shaft.

D. Insert the Blue 3/8” tubing into the Quick Connect Tubing Adapter.

E. Connect the 1/4” yellow tubing to the smaller barb and connect the 3/8” Black tubing to the larger barb.

F. Drop the entire assembly into the hole, resting on the chrome counter plate. Loosen the nut and position the

Galvanized Flange under the countertop and then securely tighten the hex nut.

G. DO NOT CUT EXCESS TUBING AT THIS POINT. YOU WILL NEED THE TUBING TO INSTALL TANK.

TIP: When connecting the tubes to the hose barbs, try using HOT water to soften the plastic tubes. When connecting the

drain lines to the saddle, make the lengths as short and straight as possible to reduce drainage noise.

Figure 4: INSTALLATION FOR DWS & DWS-PP SYSTEM

Summary of Contents for Coffee Lovers System CLS-5-90

























Search results

Summary of Contents for Coffee Lovers System CLS-5-90

Reviews:

Related manuals for Coffee Lovers System CLS-5-90

Brands by name

Popular brands

SpectraPure Coffee Lovers System CLS-5-90, Operation Manual

Search results

Summary of Contents for Coffee Lovers System CLS-5-90

Reviews:

Related manuals for Coffee Lovers System CLS-5-90

Brands by name

Popular brands