SpectraPure 100 GPD U.H.E RO/DI Owner'S Manual & Installation Instructions Download

Page: 18 / 18

SpectraPure

SpectraPure®Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

REPLACEMENT PARTS

Catalog No.

Replacement Part

Description

SF-ZZ-0.2-10

ZetaZorb

Sediment Filter

0.2 Micron Sediment Filter (1st Stage)
(Failure to use a ZetaZorb

sediment filter for replacement will

void the system’s warranty.)

CF-0.5-10

Carbon Filter

0.5 Micron Carbon Pre-Filter (2nd Stage)

MEM-0090

RO Membrane

90 GPD Membrane (3rd Stage)

DI-MC-10

MaxCap

Deionization Cartridge (4th Stage)

DI-SB-10

SilicaBuster™ DI

SilicaBuster™ Deionizaiton Cartridge (5th Stage)

FR-60

Flow Restrictor

Flow Restrictor modified for maximum water temperature

Summary of Contents for 100 GPD U.H.E RO/DI



















Search results

Summary of Contents for 100 GPD U.H.E RO/DI

Reviews:

Related manuals for 100 GPD U.H.E RO/DI

Brands by name

Popular brands

SpectraPure 100 GPD U.H.E RO/DI, Owner'S Manual & Installation Instructions

Search results

Summary of Contents for 100 GPD U.H.E RO/DI

Reviews:

Related manuals for 100 GPD U.H.E RO/DI

Brands by name

Popular brands