background image

SpectraPure

®

SpectraPure®Inc.

  

480.894.5437   Call us toll-free  1.800.685.2783    

2167 East Fifth St,    Tempe, Arizona   85281

17

THREE YEAR MANUFACTURERS WARRANTY                                                                             

SpectraPure, Inc.

®

 warrants the product to the original owner only to be free of defects in material and 

workmanship for a period of three years from the date of receipt. SpectraPure’s liability under this warranty 

shall be limited to repairing or replacing at SpectraPure’s option, without charge, F.O.B. SpectraPure’s factory, 

any product of SpectraPure’s manufacture. SpectraPure will not be liable for any cost of removal, installation, 

transportation or any other charges which may arise in connection with a warranty claim. Products which are 

sold but not manufactured by SpectraPure are subject to the warranty provided by the manufacturer of said 

products and not by SpectraPure’s warranty. SpectraPure will not be liable for damage or wear to products 

caused by abnormal operating conditions, accident, abuse, misuse, unauthorized alteration or repair or, if the 

product was not installed in accordance with SpectraPure’s or other manufacture’s printed installation and 

operating conditions, or damage caused by hot water, freezing, flood, fire or acts of God. 
SpectraPure will not be responsible for any consequential damages arising from installation or use of the product, 

including any water or mold damage due to flooding which may occur due to malfunction or faulty installation, 

including, but not limited to failure by installer to over- or under-tighten fittings, housings, and/or push-style 

fittings, or improper installation of push-style fittings. Consumable items such as prefilters and membranes are 

not covered under the three year warranty.
SpectraPure warrants (prorated) the performance of tested SpectraSelect™ RO membrane elements only, for 

one year from date of receipt by the buyer, providing that the loss of performance was not caused by  fouling, 

neglect or water conditions exceeding the feed water parameters listed in the applicable product manual (refer 

to detailed membrane warranty information). SpectraPure will, on confirmation of loss of performance during 

the warranty period, credit the prorated amount of the current catalog price of the element. The disposable 

filters and  cartridges are not covered under the warranty.
To obtain service under this warranty, the defective system or components must be returned to SpectraPure with 

proof of purchase, installation date, failure date and supporting installation data. Any defective product to be 

returned to the factory must be sent freight prepaid; documentation supporting the warranty claim and a Return 

Goods Authorization (RGA) number must be included. SpectraPure will not be liable for shipping damages due to 

the improper packaging of the returned equipment and all returned goods must also have adequate insurance 

coverage and a tracking number. 
SpectraPure will not pay for loss or damage caused directly or indirectly by the presence, growth, proliferation, 

spread or any activity of “fungus”, wet or dry rot or bacteria. Such loss or damage is excluded regardless of any 

other cause or event that contributes concurrently or in any sequence to the loss. We will not pay for loss or 

damage caused by or resulting from continuous or repeated seepage or leakage of water, or the presence or 

condensation of humidity, moisture or vapor, that occurs over a period of 14 days or more. “Fungus” and “fungi” 

mean any type or form of fungus or Mycota or any byproduct or type of infestation produced by such fungus or 

Mycota, including but not limited to, mold, mildew, mycotoxins, spores, scents or any biogenic aerosols. 
SpectraPure will not be liable for any incidental or consequential damages, losses or expenses arising from 

installation, use, or any other causes. There are no expressed or implied warranties, including merchantability or 

fitness for a particular purpose, which extend beyond those warranties described or referred to above.

* The three year limited warranty does not apply to consumable items, including but not limited to, filters 

and cartridges unless specifically stated above.

Summary of Contents for 100 GPD U.H.E RO/DI



















Reviews: