background image

 

PN: 1725-36034-001_B.doc 

83 

Certifying the Installation 

Prior to determining that an installation is complete, test the handsets 
following the sequence given in Chapter 6 

Testing a Handset

 and 

conduct a 

Site Survey

 mode test according to the directions given in 

Chapter 7 

Diagnostic Tools

.  

The installation may need some adjustments. Note any areas where 
coverage is conflicting or inadequate. Note any system difficulties and 
work with your wireless LAN and/or LAN system administrator to 
determine the cause and possible remedy. See Chapter 10 

Troubleshooting 

for clues to possible sources of difficulties. If any 

adjustments are made to the system, re-test the device in the same 
vicinity to determine if the difficulty is resolved. 
The installer should not leave the site before performing installation 
verification. 
These tests must be performed in typical operating conditions, 
especially if heavy loads occur. Testing sequence and procedure is 
different for every installation. Generally, you should organize the 
test according to area and volume, placing numerous calls to others 
who can listen while you perform coverage tests. Note any areas with 
excessive static or clarity problems and report it to a Polycom service 
engineer. 
The coverage test will also require you to put the handset in 

Site Survey

 

mode and walk the entire coverage area to verify all APs.  

Conducting a site survey 

Conduct a site survey of the installation, by walking the site looking 
for interfering 802.11 systems, adequate coverage and channel 
assignment, and correct AP configuration.  

1.

 

Referring to 

Run Site Survey

, put a handset into 

Site Survey

 in the 

Any

/

Smry

 ESSID mode.  Walk throughout the site checking for any 

expected APs or other ESSIDs.  

2.

 

Then, walk the site again, in 

MyID

/

Smry

 ESSID mode, this time 

checking that every location has adequate coverage (there should 

8

Summary of Contents for 8002




































































































Reviews: