background image

8999153EN: v1.0 18/12/2020 

15  

Original instructions (ENGLISH) 

Website:  www.spearheadmachinery.com 

 

 

2.5 

Personal Protective Equipment 

 
In general it is necessary to wear suitable clothing for the work to be carried out. In particular, as far as rotary 
mowing use, obey the following provisions: 

It is mandatory

 to use clothing which is as suitable as possible, meaning not too loose and without any 

protruding or moving parts (for example ties or necklaces). Do not wear belts, rings and chains. Always use 
sturdy safety footwear. Long hair must be tied using a specific cap. 

It is mandatory

 to use protective goggles or a mask before proceeding with the work in order to protect the 

face and eyes from vegetable fragments which may be projected outwards during rotary mowing. 

It is mandatory 

to use protective muffs in order to safeguard hearing from noise from the equipment during 

work. 
 

2.6 

Ecology And Pollution 

 

DANGER! 

  Comply with laws in force in the country the machine is being used in regarding 

use and disposal of products employed in cleaning and servicing the machine, and comply with 
the instructions issued by the manufacturer of said products and featured in the warnings on the 
relevant packaging. Keep products used for cleaning and maintenance out of reach of children. 

 

2.6.1 

Disposal 

 

When the time comes to scrap the machine, it must be disposed of through a suitable rubbish tip, in compliance 
with cur

rent legislation. Before scrapping, sort the machine’s components into plastic or rubber parts, electrical 

and electronic material.  
 
Parts made entirely from plastic, aluminium or steel can be recycled when collected by special recycling centres. 
Collect up waste oil and dispose of it through relevant collection centres. 
 

DANGER! 

  Waste oil qualifies as hazardous waste according to current law and, as such, must 

not be released into the environment; it should be recovered and disposed of through suitable 
collection centres. 

 
You must contact the relevant environment agency in your country for the collection of waste oil. 
 

2.7 

Safe Use 

 
NOTE: All references to ‘tractor’ equally apply to any power sources used to drive the machine. 
 

WARNING!

   All guards must be correctly fitted. Always ensure that all guards are in position, properly 

fitted and properly maintained. Do not attempt to operate the machine before making this check each 
time the machine is used. 
 

WARNING!

   Fit the Power Take Off (P.T.O) shaft guard & check chains. P.T.O guard check chains 

must always be attached to a suitable point on the tractor and machine to prevent movement of the 
outer plastic shields. 

 

WARNING!

   Beware of bystanders and animals. Before starting the tractor engine and moving off, 

check that it is safe to do so. Never operate the machine with bystanders or animals near or on the 
machine or tractor. Never stand in or walk through the flow of any material being discharged. Never 
stand between tractor wheels and the machine. 

 

WARNING!

   Always operate safely. Never operate the machine without maintaining full control of the 

tractor. 

 

WARNING!

   Never wear loose fitting or ragged clothing. Avoid injury - always wear clothing which 

cannot get caught in machinery. 
 

WARNING!

   Never operate the machine with any parts missing. Check the machine regularly for loose 

or damaged parts. Pay particular attention to the condition of all safety guards. Always use genuine 
Spearhead Machinery replacement parts in the interest of safety. Failures caused by the use of 

Summary of Contents for AGRICUT 180




















































Reviews: