This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2016 by Conrad Electronic SE.
*1429566_V1_0516_02_HK_m_en
c) Operation
General
• When supplying power via HDMI cable, the standby indicator lamp (7) lights up during
standby mode.
• Switch on your HDMI playback devices and your output device (e.g. TV).
• Turn on the HDMI switch using the on/off switch (8). The standby indicator lamp turns off and
the indicator lamp (3, 4, or 5) of the activated HDMI input lights up.
• Select the desired HDMI input using the Switch button (6). With every single press of the
Switch button, the system switches to the next HDMI input. Use the remote control to directly
select the desired HDMI input.
• Press the on/off switch to turn off the device after use.
Some HDMI devices feature a very low operating current and therefore do not
provide sufficient current for operating the product. If such is the case, at least one of
your connected devices must provide sufficient current.
Auto function
• The auto function detects the HDMI input connected and powered most recently.
• Press the Auto button on the remote control. The Auto indicator lamp (2) lights up.
• The device connected and activated most recently will be detected and the respective
indicator lamp lights up.
Please note that some devices supply current even when switched off. Devices that
supply power via HDMI cable when switched off will also be detected.
• The auto function can only be activated or deactivated using the remote control. Press the
Auto button again or any of the HDMI input buttons on the remote control to deactivate the
auto function.
Troubleshooting
Problem
Solution
The product does not
switch on.
• Check whether the HDMI input source has been
connected properly.
• Check whether the HDMI input source has been switched
on.
No image reception.
• Make sure your output device (e.g. TV) is switched on and
connected.
• Check whether the HDMI input source is switched on and
connected.
• Check whether the HDMI cable is of low quality. Connect
a high-quality HDMI cable.
Picture distorted or blurry.
• Check whether the cables are properly and securely
connected.
• Check whether the HDMI cable is of low quality. Connect
a high-quality HDMI cable.
No sound.
• Check the sound settings on your HDMI input source
device (e.g. DVD player) and your output device (e.g. TV).
The remote control
does not react to any
commands.
• Check whether the protective foil on the battery
compartment is still attached. If yes, remove it.
• Check whether the battery must be replaced.
• Make sure there are not objects located between the
remote control and the IR receiver, as such could obstruct
the signal transmission.
• Check whether the max. range of 6 meters has been
exceeded.
Cleaning and care
• Under no circumstances use aggressive cleanings agents, cleaning alcohol or other chemical
solutions since these can penetrate the housing or impair functionality.
•
Never submerge the product in water or other liquids.
•
Clean the product with a dry, fibre-free cloth.
Disposal
a) Product
Electronic devices are recyclable waste and must not be disposed of in the household
waste. At the end of its service life, dispose of the product in accordance with
applicable regulatory guidelines.
Remove any inserted batteries and dispose of them separately from the product.
b) Batteries
You as the end user are required by law (Battery Ordinance) to return all used
batteries. Disposing of them in the household waste is prohibited.
Contaminated batteries are labelled with this symbol to indicate that disposal in the
domestic waste is forbidden. The designations for the heavy metals involved are:
Cd = Cadmium, Hg = Mercury, Pb = Lead (name on batteries, e.g. below the trash
icon on the left).
Used batteries can be returned to collection points in your municipality, our stores or wherever
batteries are sold.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical data
a) HDMI switch
DDC input/output .......................... 5Vp-p (TTL)
Operating current .......................... max. 350 mA
Input.............................................. 3x HDMI
Output ........................................... 1x HDMI
Frame rate/resolution ................... 24/50/60 images/minute:
1080p / 1080i / 720p / 576p / 576i / 480p / 480i
24/30 images/minute:
2160p
Colour depth/resolution ................ 24, 30, 36 bit:
1080p / 1080i / 720p / 576p / 576i / 480p / 480i
24 bit:
2160p
Supported audio format ................ DTS-HD / Dolby-trueHD / LPCM7.1 / DTS / Dolby-AC3 / DSD
Bandwidth ..................................... max. 25 MHz
IR extension cord length ............... approx. 115 cm
Operating/storage conditions ........ -10 to +55 ºC, 10 % – 85 % RH (non-condensing)
Dimensions (W x H x D) ............... 95 x 20 x 53 mm
Weight .......................................... 122 g
b) Remote control
Battery type .................................. button cell CR2025
Range ........................................... max. 6 meters (unobstructed)