7
Original instructions
EN
17. Safety guard mounting plate
18. Screw
19. Fence
20. Side extension arms
21. Mounting hole
22. Mitre table slot insert (kerf plate)
23. Mitre table lock handle
24. Mitre lock latch
25. Mitre scale
26. Mitre table
27. Spindle lock button
28. Laser guide ON/OFF switch
29. Slide bars
30. Slide bar lock
31. Lock pin
32. Bevel lock lever
33. Clamp knob
34. Base plate
36. Philips head screw
37. Depth adjusting lock nut
(Fig. 15)
38. Circular saw blade
(Fig. 25)
39. Blade securing bolt (left thread)
(Fig. 25)
40. Inner flange
(Fig. 25)
41. Outer flange
(Fig. 25)
VII - Operation instructions
This SPARKY power tool is supplied from single-phase
alternating current mains. It is double insulated accord-
ing to EN 61029 and IЕС 61029 and can be connected
to grounded or not grounded sockets. This power tool
is radio suppressed in compliance with EMC Directive
2004/108/EC.
This power tool is designed for making cross, bevel, mi-
tre and compound cuts in wood and medium density
fibre board
PRIOR TO INITIAL OPERATION
Before starting to operate the power tool, always check
the following:
▪
Make sure power supply voltage corresponds to the
value, indicated on the name plate with technical data
of the machine.
▪ Always check the position of ON/OFF switch. The
power tool must be connected to the power supply
socket only when this switch is in OFF position.
▪
Always inspect the blade. Use only well ground
blades. Blades with cracks and indents should be re-
placed immediately. Never use HSS-blades.
▪
Make sure that all moving parts of the blade guard
move freely.
▪
Make sure the work piece or the material is well se-
cured.
▪
Make sure that the cord and the plug are in order. If the
replacement of the supply cord is necessary, this has
to be done by the manufacturer or his agent in order
to avoid a safety hazard.
MAXIMAL WORKPIECE DIMENSIONS
Horizontal cuts,
mitre angle
Height x Width, mm
Vertical cuts,
bevel angle 0°
Compound cuts,
bevel angle 45° left
0°
300 x 65 mm
300 x 35 mm
15°
290 x 65 mm
290 x 35 mm
22.5°
275 x 65 mm
275 x 35 mm
30°
260 x 65 mm
260 x 35 mm
45°
210 x 65 mm
210 x 35 mm
ACCESSORIES
The tool is supplied with the following accessories: circu-
lar saw blade (fitted), dust bag, side extension arms - 2
pcs., work clamp; spanner; hex key (allen key).
To achieve best results we recommend using genuine
SPARKY accessories.
BENCH MOUNTING
The saw base has holes to facilitate bench mounting.
(Fig. 1)
Attach the saw to a level, horizontal bench or work ta-
ble using four M8 bolts, nuts and washers (not supplied)
though the fixing holes in the saw base.
NOTE:
If desired, you can mount the saw to a piece of
13 mm or thicker plywood which can then be clamped
to your work support or moved to other job sites and re-
clamped.
WARNING:
Make sure that the mounting sur-
face is not warped, as uneven surface can cause bind-
ing and inaccurate sawing.
To mount the saw, proceed as follows:
1. Mark the mounting surface the place for the four
holes.
2. Drill four Ø10mm holes through the surface.
3. Place the machine on the surface and align the
holes in the base plate with the drilled hole in the
mounting surface. Attach the machine using M8
bolts, nuts and washers.
DUST BAG
To reduce build-up of saw dust, fit the dust bag (6) over
the dust extraction port (8).
(Fig.2)
To empty the dust bag, remove it from the dust extraction
port and unzip the slide fastener.
To ensure efficiency, empty the dust bag when it is filled
to approximately 2/3 of its capacity. This allows better
airflow through the bag.
SIDE EXTENSION ARMS
The side extension arms (20) are used for support-
ing long workpieces to prevent them from bowing and
sub¬sequent pinching on the blade during cutting.
(Fig.3)
To install side extension arms, simply insert the ends of
extensions into the holes in both sides of the base. Se-
cure them in place by tightening clamp knobs (33).
pages-TKN 65.indd 7
29.1.2013 г. 10:55:11 ч.
Та
ше
в
-
Га
лв
ин
г
ОО
Д
www.tashev-galving.com
