background image

SPARK TITAN USER MANUAL SF-X8 

A15

CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD

www.sparkfabrica.com

The heating function of the second channel DMX value is 240~255, and it takes about 5 

minutes to preheat after turning on.

When heating is turned on, the <HEAT> indicator light on the machine will turn to red, and the 

<READY> indicator light flashes green to indicate that the machine is heating.

Heating will complete after the <READY> indicator light turns green for a long time, and the 

spark machine will enter sparking status.

When using the Pyro Sim Controller,the screen will display the real-time temperature of each 

machine. When the temperature value of the control board turns green, it means that the 

heating is completed and the machine enters the status of sparking.

5.5.2 TURN ON HEATING FUNCTION

5.5    START TO SPARK

The machine can be controlled by Pyro Sim Controller console or DMX512 console.

5.5.1 TURN ON CONSOLE’S POWER

5.4  SWIPE RFID TIME CARD

Each swipe of the card can be recharged for 12 minutes, and each machine can swipe up to 

2 time cards for 24 minutes at most.The card can only be swiped again when the remaining 

time is less than 20 minutes.

If the customer breaks the card swiping function or cancels the card swiping function at the 

customer's request, no quality guarantee and after-sales service will be provided by Spark 

Fabrica. Spark Fabrica shall not be liable for any accidents and losses about this.

In order to avoid machine failure or other safety accidents caused by bad-qualified consumables, this

product can only be used with special RFID time card.

Summary of Contents for SPARK TITAN SF-X8

























Reviews: