background image

 

Euro Kitchen Appliances Inc. 7272 Buller Ave, Burnaby BC     www.KitchenHoods.ca  

 

 

 
 

•  All measurements are in millimetres.

 

Overall (3388C-IM): 

 

 

 
 

SAFETY WARNING: Never put your hand into area housing the fan while the fan is operating!

 

For optimal operation, clean range hood and all baffle/spacer/filter/grease tunnel/oil container regularly. Regular care will 
help preserve the appearance of the range hood.

 

 

Cleaning Exterior surfaces:

 

•  Clean  periodically  with  hot  soapy  water  and  clean  cotton  cloth.  DO  NOT  use  corrosive  or  abrasive  detergent  (e.g.

 

Comet Power Scrub

®

, EZ-Off

®  

oven cleaner), or steel wool/scoring pads, which will scratch and damage the stainless 

steel surface. For heavier soil use liquid degrease such as “Formula 409

®

” or “Fantastic

®

” brand cleaner.

 

•  If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting 

cleaning solution onto or into the control panel. Follow directions of the stainless steel cleaner. 

CAUTION: DO NOT 

leave on too long as this may cause damage to hood finish. 

Use soft towel to wipe off the cleaning solution, gently 

rub off any stubborn spots. Use dry soft towel to dry the hood.

 

•  After cleaning, you may use non-abrasive stainless steel polish such as 3M

® 

or ZEP

®

, to polish and buff out the stainless 

luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain.

 

•  DO NOT allow deposits to accumulate or remain on the hood.

 

•  DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting.

 

•  DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel 

for extended periods. Many of these compounds contain chemicals, which may be harmful. Rinse with water after  

     exposure and wipe dry with a clean cloth. 
 
 
 

 
 
 
 

Model SV400D

Model shown:

SV400D-I30, I36

Summary of Contents for 3503e2























Reviews: