background image

 

Form No. 43539500 

 

30

 

July 2021 A 

 
 
 
 

 

GAS-FIRED PRODUCTS LIMITED WARRANTY 

LIMITED WARRANTY 

Gas-Fired  Products,  Inc.  (GFP),  the  manufacturer,  warrants  the  original  owner  of  any  Space-Ray  Poultry  Heating 
Product that it will be free from defects in material or workmanship under normal use and service.  The heater(s) shall 
be  installed,  used  and  ma

intained  strictly  in  accordance  with  the  manufacturer’s  instructions.    The  manufacturer’s 

sole  obligation  under  this  warranty  is  limited  to  furnishing  replacement  parts,  F.O.B.  Charlotte,  NC,  for  12  months 
from the date of installation, or 18 months from the date of shipment by the manufacturer, whichever period expires 
first.    Labor  charges  for  the  removal  of  defective  parts  or  the  installation  of  replacement  parts  are  not  included. 
Additionally, the manufacturer will at any time during a 36 month period after installation or 42 months from the date 
of shipment by the manufacturer, whichever period expires first, furnish at no cost to the original owner, replacement 
parts for the heaters that have the model number prefix: PCA/PCS, PBF, FUS and PCA SS (Defender) tube heaters. 

ADDITIONAL  WARRANTY  ON  MODEL  SRB40,  TRU40  AND  LoPro  BROODER  EMITTERS:

  

Additionally, the manufacturer will at any time during a 36 month period after installation or 42 months from the date 
of shipment by the manufacturer, whichever period expires first, furnish at no cost to the original owner, replacement 
emitter  assemblies  or  heat  exchanger  tubes  which  have  become  inoperative  by  reason  of  any  defect  in  our 
workmanship,  materials  or  construction.    The  manufacturer  will  not  be  responsible  for  labor  charges  incurred  for 
removal or installation of emitters.  Any transportation charges involved in the return or repair are excluded. 

ADDITIONAL WARRANTY ON MODEL PCA, PBF CALORIZED TUBE HEATER HEAT EXCHANGER:

  

Additionally,  the  manufacturer  will  at  any  time  during  a  120  month  period  after  installation  or  126  months  from  the 
date  of  shipment  by  the  manufacturer,  whichever  period  expires  first,  furnish  at  no  cost  to  the  original  owner, 
replacement emitter assemblies or heat exchanger tubes which have become inoperative by reason of any defect in 
our workmanship, materials or construction.  The manufacturer will not be responsible for labor charges incurred for 
removal or installation of emitters.  Any transportation charges involved in the return or repair are excluded. 

WARNING:

  

Manufacturer’s warranty shall not apply and GFP is not responsible for damages caused with regard 

to:  (a)    circumstances  where  gas  pressure  to  each  heater  is  higher  than  that  specified  for  each  heater;  (b) 
circumstances  where  the  type  of  gas is  different  than  the  type  of  gas  noted  on  the name  plate  for  each  heater;  (c) 
water damage to gas controls; (d) circumstances where any acid or acid-based product causes damage to the metal 
components; or (e) any heater or component part which has been repaired or replaced with other than factory parts, 
modified  in  any  way,  misused  or  damaged,  or  which  has  been  used  contrary  to  the  manufacturer’s  written 
instructions. 

LIMITATION  OF  WARRANTY:

   

THERE  ARE  NO  WARRANTIES,  EXPRESS  OR  IMPLIED,  WHICH  EXTEND 

BEYOND  THE  DESCRIPTION  ON  THE  FACE  HEREOF.    WITHOUT  LIMITING  THE  FOREGOING,  THE 
MANUFACTURER  EXPRESSLY  EXCLUDES  ANY  AND  ALL  IMPLIED  WARRANTIES,  INCLUDING  BUT  NOT 
LIMITED  TO  ANY  IMPLIED  WARRANTY  OF  FITNESS  FOR  A  PARTICULAR  PURPOSE  AND  ANY  IMPLIED 
WARRANTY OF MERCHANTABILITY FOR ITS PRODUCTS. 

If  any  provision  of  this  warranty  is  found  to  be  void,  unenforceable  or  unconscionable,  then  that  portion  is  hereby 
severed and the remainder of this warranty is hereby saved and shall remain in force. 

EXCLUSIVE  REMEDY:

   

The  sole  and  exclusive  remedy  under  this  warranty  is  the  replacement  of  the  defective 

parts or brooders as hereinabove specified.  THE MANUFACTURER DOES HEREBY EXPRESSLY EXCLUDE ANY 
AND  ALL  LIABILITY  FOR  INCIDENTAL  OR  CONSEQUENTIAL  DAMAGES  UNDER  THIS  OR  ANY  OTHER 
WARRANTY.  Without intending to limit the aforesaid exclusion, THE MANUFACTURER DOES HEREBY EXCLUDE 
ANY  LIABILITY  UNDER  THIS  OR  ANY  OTHER  WARRANTY  FOR  INJURIES  OR  COMMERCIAL  LOSSES  TO 
PROPERTY THAT RESULT FROM THE OPERATION, PROPER OR IMPROPER, OF ITS PRODUCTS. 

ADDITIONAL  TERMS:

   

Manufacturer  assumes  no  liability  for  delay  in  performing  its  obligations  under  this 

warranty.    Manufacturer  assumes  no  liability  for  failure  in  performing  its  obligations  there  under  if  failure  results 
directly or indirectly from any cause beyond its control, including but not limited to acts of God, acts of Government, 
floods, fires, shortages of materials, strikes and other labor difficulties or delays or failures of transportation facilities. 

This is a Non-Residential product.  Installation and service shall be by a Licensed Contractor and in accordance with 
National and Local Codes. When presenting warranty claims, proof of date of purchase must be submitted. 

Summary of Contents for LoPro LPBH40-L5

































Reviews: