background image

 

 

 

 

Operation Manual

 

10Base-T

 

Ethernet Converter 

 

 

 

 

 

 

AR-727CM 

Table of Contents 

 

 

 

 

1. Introduction    

1.1  Features  

 

                     ----------------------------------- 

1

 

 

1.2  Specifications 

                     ----------------------------------- 

   1.3  Applications   

                     ----------------------------------- 

2. 

Overview    

2.1  Dimensions and mounting                 ----------------------------------- 

 

 2.2  LED Indicators 

                     ------------------------------------ 

 

 2.3  DIP Switch Settings                   -------------------------------------   3 

 

  2.4  D-SUB Connector pin out               ------------------------------------ 

3. Configuration 

3.1  Reset To Factory Default               ----------------------------------- 

3.2 

DHCP 

Function 

   

 

 

          ----------------------------------- 

 

  3.3   How to configure the IP address assigned to your AR-727CM device        5 

 

  3.3.1 

Get IP address by using Net727i software ------------------------- 5 

 

  3.3.2 

Get IP address by DHCP Server  

----------------------------------- 8  

 

  3.3.3 

Get IP address by Hyper-Terminal function of the Window  ------- 

10 

2005/12/16

 

 

 

                                                                                             

 

Summary of Contents for AR-727CM













Reviews: