SOYAL
®
AR-101-H/U
V221024
ACCESS & INDUSTRIAL CONTROL
- 5 -
Factory Reset
Selection= 0(none value)/ 1(1 x each value)
[e.g.] ??? value of Enable “Auto Open” + ”Exit by Push ”Anti-pass-back”
=(0x1)+(0x2)+(1X4)+(1x16)+(0x32)+(0x64)+(1x128)=148 ; As a result of that, the command will be 20 148 .
20 ???
※
Default Value
Function
Selection
Value Application
Attendance
※
0: Yes
1: No
001 Networking
Auto Re-lock
※
0: Disable
1: Enable
002 Networking/Stand-Alone
Auto Open
※
0: Disable
1: Enable
004 Networking/Stand-Alone
Door open button input
0: Disable
※
1: Enable
016 Networking/Stand-Alone
Master Controller of Network
※
0: Slave
1: Mater
032 Networking
24 ???
※
Default Value
Function
Selection
Value Application
Auto-open door without cards at auto open zone
※
0: Disable
1: Enable
001 Networking/Stand-Alone
Alarm Output/ Lift Control
※
0: Alarm Output 1: Lift Control
002 Networking/Stand-Alone
Stop Alarm by door close or by push button
0: None
※
1: Yes
064 Networking/Stand-Alone
28 ???
※
Default Value
Function
Selection
Value Application
Dual Door Control
※
0: Disable
1: Enable
064 Networking/Stand-Alone
Force Open Alarm Output
※
0: Disable
1: Enable
128 Networking/Stand-Alone
Enable:
Enter program mode
→
After door open :
The normal procedure to open door
→
Input 4-digit arming PWD
→
Disable:
Enter program mode
→
Do not open the door
：
→
Input 4-digit arming PWD
→
Present a valid card
Enable/Disable Arming status
(for M4/M8)
:
More Details:
SOYAL Security Related Function
※
[The normal procedure to open door] can refer to [Access Mode].
※
Read the [Command List-Arming /Duress Function Setting] below to modify arming PWD.
※
M6 is Standalone Mode, the mode is without Arming /Duress Function.
Enter Programming Mode
Without Enter Programming Mode (Standby Mode): Enter Arming Code
（
default value of arming PWD is: 1234
）
34 ???
Function
Selection
Value Application
※
Default Value
Enable the RF after door sensor closed to GND
Invalid card to activate alarm relay
Turn off all sounds of beeper
Mute the sounds of egress button (RTE)
Reserved
Keep beeing while arming is enabled
Door relay connected to AR-721RB (suited to models without relay built-in)
Arm relay connected to AR-721RB (suited to models with relay built-in)
※
0: Deactivate
※
0: Deactivate
※
0: Deactivate
※
0: Deactivate
※
0: Deactivate
※
0: Deactivate
※
0: Deactivate
※
0: Deactivate
Networking/Standalone
Networking/Standalone
Networking/Standalone
Networking/Standalone
Networking/Standalone
Networking/Standalone
Networking/Standalone
Networking/Standalone
001
002
003
004
016
032
064
128
1: Activate
1: Activate
1: Activate
1: Activate
1: Activate
1: Activate
1: Activate
1: Activate
Weighted Value Manual :
"Selection"
of the function that you need is either
have 0 or 1 value.
Substract the
"Value"
of each Option with Selection.
Function = [0(deactive)*Value] ; [1(activate)*Value]
Add up all of the Function per Compound Command
(20 , 24 ,etc)
Step 1:
Select the
"Function"
that you need for each
Compound Command category (20 , 24 , etc)
Step 2:
Step 3:
Step 4:
Compound Command Function List
Reset User Data
Reset User Data &Controller Parameter
(incl. Master Code)
Reset User Data &Controller Parameter
(incl. Master Code) & Reset Parameter Setting- SOR
Enter program mode
→
29
29
→
Exit the programming mode
Enter program mode
→
29
20
→
Exit the programming mode
Enter program mode
→
29
21
→
Exit the programming mode
※
If forgotten the current Master Code, Reset through software tools is required. Please refer to the FAQ for more detail
：