SOYAL
®
AR-101-H/U
V221024
ACCESS & INDUSTRIAL CONTROL
- 3 -
323DMaster
2
1
LB-
LA+
2
1
AR-321-CM
About Master Card
Enter the program mode
Input 123456 or PPPPPP
[e.g.] The Default Value= 123456, if already changed the Master Code= 876112, input
876112
→
program mode accessed
Exit the program mode
Input
Operation process
Master Code modification
Access programming mode
→
09 PPPPPPRRRRRR [Input the 6-digit new master code twice.]
[e.g.] Set the Master code to be 876112, input
123456
→
09 876112876112
A. Enter/ Exit Program Mode
Adding Tag
Present Master Card
Deleting All Tags
Present Master Card
P.S. Once MASTER CARD is presented after one
warning beep, all card data will be cleared.
After 3 short beeps
[Access programming mode]
After 3 short beeps
[Access programming mode]
Present the new card or cards
one by one till finished the adding.
1 long warning beep after 2sec.
Present Master Card
[Exit programming mode]
5 short beeps after 5sec: cards cleared
1.
1.
2.
2.
3.
3.
4.
4.
MASTER CARD Setting for keyless editing
RS485 USB Converter
Use the MASTER CARD software
Input the MASTER CARD number, and press [Write].
Cut off and then transmit the power, the master card number will be activated.
Present the card, and the reader will flash green light 3 times and sound 3 beeps. Then the card becomes MASTER CARD and accesses programming
mode.If MASTER CARD is presented again, it will exit programming mode.
Green
Blue
Plug in cable , the wire connection is as below figure. After connection, then have power transmission to controller.
( Below programming is for AR-101-H only )
P2
Mode4 / Mode6 / Mode8
※
Mode 6,
the number of users up to 65535, since it reads
CARD CODE
(5 digits) only, unlike that Mode4/Mode8 read
SITE CODE
and
CARD CODE
(10 digits).
If Access Mode setting to use the PIN,
it
need to external the K-series Readers.
Mode Networking/
Stand-Alone
User
Capacity
Access Mode
Auto-show
Duty time
Event log
Capacity
120
Holidays
Anti
force
Time
Zone
Lift
Control
Anti-pass-
back
M4
Networking/
Stand-Alone
1,024
1.Card only
2.Card and PIN
(4-digit PIN)
+
3.Card or User address
(5-digit)
+ Individual PIN
(4-digit
individual PIN)
+
Yes
1,200
Yes
Yes
No
32
Yes
M6 Stand-Alone
65,535
1.Card only
2.Card and PIN
(4-digit public PIN= Arming PWD)
+
3.Card or PIN
(4-digit public PIN= Duress code)
No
No
No
No
No
No
No
M8
(Default
Value)
Networking/
Stand-Alone
1,024
1.Card only
2.Card and PIN
(4-digit individual PIN)
+
3.Card or PIN
(4-digit individual PIN)
Yes
1,200
Yes
Yes
No
32
Yes
※
M6:
the user capacity can be 65535 because it only reads 5-digits
CARD CODE
, while in
M4/M8
it reads both
SITE CODE
and
CARD CODE
(10 digits).
Enter program mode
→
04 N [N=4/6/8]
※
Set up M4/M6/M8 :
※
Default Card UID Length is 4 (Could not change by command and only be able to change by customized firmware)
(Note: The modification of controller mode between M4/M8(networking) and M6(standalone) will reset the data, user data will be
required to rebuild.)