Disabled vehicle
If the vehicle is disabled, right and left turn indicator check lights
are blinking alternately in the instrument cluster. Except it, an
error code 00:XX is displayed for owner information on the vehicle
clock display after switching the ignition on.
00:31
Manipulation of key data in CAS internal memory
00:32
Physical disconnection of CAS control unit
00:33
Disconnection of vehicle battery
00:34
Unauthorized vehicle access
00:35
CAS not responding to ATS01 data telegrams
00:36
Wrong PIN code entered 3 times
00:37
Excessive vehicle tilt / shaking
Vehicle could be enabled either by entering personal PIN code
(via iDrive or smartphone), by elapsing the waiting period
(optional), by smartphone or by authorized service technician.
Please keep your personal PIN code in safe place. You will receive
the PIN code after installation of the immobilizer.
Attention!
Any complaints or claims due to absence of personal PIN code will
be rejected!
Enabling the vehicle using personal PIN code:
a)
Close all doors and front/ rear lid (don't lock the vehicle!)
b)
Insert original transponder into the starting slot and/or switch
on ignition using START / STOP button. Wait 10 seconds until
acoustic signal subsides.
c)
Using iDrive controller or on board computer switch enter the
PIN code as date (see vehicle owners manual)
d)
Lock the vehicle using interior LOCK/UNLOCK button (both
turn indicator check lights are on)
e)
After one second: Unlock the vehicle using the same button
(check lights are switched off and audible signal is generated)
f)
Remove the key from slot or switch off ignition and wait until
the green light P on the gearshift lever is switched off. * After
successfull procedure the previous date is automatically
restored.
Note:
You have only 3 attempts to enter the personal PIN code. After
third wrong attempt the vehicle will be blocked for additional 60
minutes (turn indicator check lights in instrument cluster are
flashing simultaneously). Entering the PIN code is possible only
after elapsing this time period.
Warning!!
When the vehicle is blocked and yellow crossed key symbol is
displayed in the instrument cluster, key data were probably
manipulated. Please immediately contact your service or call the
Hotline in this case!
Enabling the vehicle using waiting period:
In case of loss or absence of the personal PIN code, you can
enable the vehicle via elapsing the preset waiting period (optional).
4
The period starts immediately after the vehicle is disabled. After
elapsing the period, vehicle will be automatically enabled.
Note:
This function is optional and is activated only on special customer
request. Customer has to sign, that he is aware about potential
safety risk.
New key
After installation of the ATS02, all active key data are copied into
the immobilizer memory. From this moment, only active keys are
accepted. If a new original key is ordered, it has to be authorized
prior to use.
Authorisation of the new key:
a)
Close all doors and front/ rear lid (don't lock the vehicle!)
b)
Insert new transponder into the starting slot and / or switch
ignition on (vehicle will be disabled and crossed key symbol
displayed in the instrument cluster). To authorize the key,
enable the vehicle using personal PIN code.
Additional start protection
This option protects your vehicle from unauthorized start even in
case of abuse of Comfort Access system (option 322).
If active, engine can be started only after entering
a two-digit start
code via the multifunction steering wheel.
Engine start authorization:
a)
Use the – / + buttons to enter your start code (XY).
Entering: press button “ –” X-times and button “+“ Y-times
b)
Confirm entered code by pressing the MODE button.
In case of successful entry an acoustic signal is generated.
Attention!!
After three wrong entries the vehicle will be disabled. Blocking
code 00:36 is displayed on vehicle clock display.
Emergency/Limited mode
In case of serious fault the ATS02 is switched to emergency mode.
In this mode (if the fault allows), all the blocking functions are
deactivated and the yellow FAULT symbol is displayed in the
instrument cluster. If the fault will not cause the complete failure
of the system, fault symbol and fault code (00:XX) are displayed,
too. In this situation the ATS02 works in limited mode (your
vehicle is still reliably protected).
Note:
In case of failure, immediately visit your authorized dealer or call
the Hotline. You will avoid potential security risks.
* - Function depends on type and equipment of the vehicle.
5
Operating instructions
ATS 02
Electronic immobilizer for BMW vehicles
