Introduction
1
The Southwire 40040S Continuity Tester provides a simple way of
checking continuity on wires and cables. The bright LEDs and loud
pulsating beeper provide a positive indication of continuity and polarity.
The detachable remote indicator can be used to trace multiple cable runs.
With proper use, this tester will provide many years of reliable service.
WARNINGS
• Read, understand and follow Safety Rules and Operating Instructions
in this manual before using this tester.
• Do not connect the tester to a live circuit. Connecting the tester to
voltage presents a shock hazard and may damage the tester.
• Do not use if the tester or test leads appear damaged or is not
operating properly.
• Do not use the tester in a wet or damp environment or during
electrical storms.
• Do not use the tester near explosive gases, dust or vapor.
• Replace the battery as soon as the low battery warning appears.
Maintenance
1. KEEP THE TESTER DRY. If it gets wet, wipe it off.
2. USE AND STORE THE TESTER IN NORMAL TEMPERATURES.
Temperature extremes can shorten the life of the electronic parts
and distort or melt plastic parts.
3. HANDLE THE TESTER GENTLY AND CAREFULLY. Dropping it can
damage the electronic parts or the case.
4. KEEP THE TESTER CLEAN. Wipe the case occasionally with a
damp cloth. DO NOT use chemicals, cleaning solvents, or detergents.
5. USE ONLY FRESH BATTERIES OF THE RECOMMENDED SIZE AND
TYPE. Remove old or weak batteries so they do not leak and damage
the unit.
6. IF THE TESTER IS TO BE STORED FOR A LONG PERIOD OF TIME,
the battery should be removed to prevent damage to the meter.
2
General Specifications
Beeper
Distance
Operating Temperature
Storage Temperature
Operating Humidity
Battery
Dimensions
Weight
85dB
10,000 feet (3000 meters) minimum, 26 AWG
10 to 113°F (-12 to 45°C)
-4 to 140°F (-20 to 60°C)
10 to 90% RH (non-condensing)
One 9 volt battery
5.11” x 2.05” x 1.30” (130 x 52 x 33mm)
4.5oz (129g)
Tester Description
1. Red LED continuity indicator (- Polarity)
2. Green LED continuity indicator (+ Polarity)
3. On/Off button
4. Power on LED (flashes when battery is low)
5. Detachable remote
6. Remote bi-color LED continuity
and polarity indicator
40040S
Continuity Tester
POWER
Tester
Remote
n/a
R
B
R
B
R
B
R
B
R
B
40040S
Remote
6.
1.
2.
3.
4.
5.
FCC COMPLIANCE
Users of this product are cautioned not to make modifications or changes that are not approved by Southwire Company, LLC. Doing so may void
the compliance of this product with applicable FCC requirements and may result in the loss of the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that can cause
undesired operation.
FCC Digital Emissions Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the radio or television receiving antenna.
• Increase the separation between the computer equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.
• Consult the dealer or an experienced radio television technician for help.
Canadian Digital Apparatus Compliance
CAN ICES-3 (B)/NMB-3(B)
