ON A WALL PHONE PLATE:
a. Plug the short telephone line
cord into the jack in the Base
bottom and into the jack on the
plate.
b. Hang the BASE on the two
pins and push the BASE down
to lock it on.
c. Plug the COIL CORD into the
HANDSET and BASE jacks.
ON THE WALL WITHOUT A PLATE:
a. Install 2 screws with anchors
into the wall, one above the
other, 3-1/4” apart, extending
3/16” out from the wall, to hold
the base securely.
b. Install the long telephone line
cord into jack in the BASE,
thread it through the groove
toward the front of the unit, and
plug it into the modular wall
jack as shown.
c. Hang the base on the screws
and pull it down to lock it on.
d. Plug the COIL CORD into the
HANDSET and BASE jacks.
NOTE: There is a provision for holding the handset off
hook when the telephone is wall mounted. Position the
handset on the notch above the dial tone reset key. This
is a convenient feature when you need to call another
person to the phone or if you are interrupted during the
conversation.
4. TONE/PULSE SWITCH
SET SWITCH TO YOUR TYPE OF SERVICE. If you don’t
know whether you have tone or pulse:
a. Put the SWITCH on “TONE”.
b. When you have a dial tone, press any BUTTON on
the DIAL PAD. If the dial tone stops, leave it on “TONE”.
If not, change the setting to “PULSE”. Mixed Dialing:
If you have Pulse service, you can temporarily switch
to “Tone” dialing if required for various custom
services. Press the “
*
” button and all further dialing
functions will be in “Tone”, until you end the call.
OPERATIONAL FEATURES
REDIAL BUTTON
Automatically redials last number called (up to 32 digits
in pulse mode and 31 digits in tone mode), if the number
was busy or unanswered.
a. Lift the HANDSET.
b. Press the REDIAL BUTTON.
MUTE BUTTON
Prevent sound from your room from being heard by
another party on the phone.
Press and hold the MUTE BUTTON as long as you want
this feature activated.
STORE BUTTON (TO PROGRAM)
You may store up to 13 frequently called phone numbers
(maximum 16 digits in pulse mode and 15 digits in tone
mode) in your FC2548/FM4000: 3 one-touch priority
numbers, which can be dialed at the touch of a single
button, and 10 additional numbers which require only
2-button dialing.
HOW TO PROGRAM YOUR 3 ONE-TOUCH PRIORITY
NUMBERS:
1. Lift the handset, listen for dial tone.
2. Press and release the STORE BUTTON.
3. Dial the number to be stored. (The telephone will not
dial out.)
4. Press and release STORE BUTTON again.
5. Press M1, M2 or M3 respectively for each of the 3
one-touch priority numbers you wish to store. Replace
handset in cradle.
HOW TO PROGRAMYOUR 10 FREQUENTLY CALLED
NUMBERS:
1. Lift the handset. Listen for dial tone.
2. Press and release the STORE BUTTON.
3. Dial the number to be stored. (The telephone will not
dial out.)
4. Press and release STORE BUTTON again.
5. Press the Number Button (0-9) on the telephone key
pad where you want the number stored. Replace
handset in cradle.
An index Card is located on the base for use in writing
down the person’s name stored in memory.
MEMORY BUTTON (TO RETRIEVE)
How to dial one-touch priority numbers stored in Memory:
1. Lift the handset. Listen for dial tone.
2. Press M1, M2 or M3 respectively where the desired
number is stored.
How to dial a frequently called number stored in Memory:
1. Lift the handset. Listen for dial tone.
2. Press and release Memory Button.
3. Press the Number Button (0-9) where desired number
is stored.
ERASING A STORED NUMBER
Simply repeat the steps outlined in “How to Program”
section replacing the previously stored number with
another.
RESET BUTTON
At the end of a call, you can make your next call without
replacing the HANDSET in the cradle. Press and hold
RESET to disconnect the telephone.
FLASH (CALL WAIT)
*
BUTTON
Allows you to access the Call Waiting service from your
local telephone company
*
or access a new dial tone.
*
Requires special service from your local telephone
company.
RINGER OFF/LOW/HIGH
Your phone features a harmonic dual tone ringer which
can be adjusted to a loud(High) or soft(Low) sound level.
When you don’t want to be disturbed, slide the switch to
the “Off” position. Now you can still make outgoing calls
without being disturbed by incoming calls.
LIGHTED KEYPAD
For better visibility when dialing in a dim light, a lighted
dial pad is provided.
RECEIVER VOLUME CONTROL
The RECEIVER VOLUME CONTROL is located on the
side of your handset. This control allows you to adjust
your handset volume from normal to high for a more
comfortable listening level.
CARE AND MAINTENANCE
To clean, use a soft cloth dampened in a mild detergent.
Never use abrasives or solvents or spray cleaners directly
on the telephone.
HEARING AID COMPATIBILITY
THE FC2548/FM4000 is compatible with inductively
coupled hearing aids.
FCC WANTS YOU TO KNOW
This equipment complies with Part 68 of the FCC rules.
On the bottom of the base of this equipment is a label
that contains, among other information, the FCC
Registration Number and Ringer Equivalence Number
(REN) for this equipment. You must, upon request,
provide this information to your telephone company. The
REN is useful to determine the quantity of devices you
may connect to your telephone line and still have all of
those devices ring when your telephone number is called.
In most, but not all areas, the sum of the RENs of all
devices connected to one line should not exceed five
(5.0). To be certain of the number of devices you may
connect to your line, as determined by the REN, you
should contact your local telephone company to
determine the maximum REN for your calling area.
If your telephone equipment causes harm to the
telephone network, the telephone company may
discontinue your service temporarily. If possible, they will
notify you in advance. But if advance notice isn’t practical,
you will be notified as soon as possible. You will be
informed of your right to file a complaint with the FCC.
5
6
7
8
Sold by:
http://www.TWAcomm.com
Toll Free: (877) 892-2666
