Southland S-WLE-0799-F2N Operator'S Manual Download Page 2

Page: 2 / 43

Questions? Call Toll Free at 1-800-737-2112

Indicates WARNING, DANGER, or CAUTION.

Wear eye protection complying with ANSI

Z87.1 and hearing protection.

Read operator’s manual before operating

this machine. Failure to follow directions

could result in serious injury.

Disconnect spark plug wire when not in use

or before servicing, cleaning, or performing

maintenance on the unit.

Thrown objects. Remove all rocks, stones,

and foreign objects which could be thrown by

machine

Engine exhaust contains carbon monoxide,

an odorless and deadly gas. NEVER run unit

indoors or in a poorly ventilated area.

Do not use if children or bystanders are

present.

Do NOT touch hot muffler or cylinder.

These parts are extremely hot from opera-

tion and may remain hot for a short time

after operation.

Rotating parts can cause serious injury. Keep

hands and feet away.

To reduce risk of fire, clean spilled gas and

oil and keep unit free from debris. Gasoline is

extremely flammable. Allow machine to cool

before refueling.

Safety Definitions

• Save these instructions

Safety Warning Symbols

Control and Operating Symbols

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor/moderate injury or

equipment/property damage.

DANGER

CAUTION

WARNING

The following symbols are used on the product and in this manual to alert the operator of potential safety hazards. Read

them carefully, and understand their meaning.

Safety Alert Symbols

The following symbols can be found on your edger. Carefully read and understand their meaning.

Important

Safety

Information

Oil Fill Location

Do Not Overfill

Gasoline Fill Location

Start Lever

Release lever to stop engine

Engage lever to start/run engine

Choke/Cold Start

Run/Warm Start

Always check that the ground wires

are connected before running the unit

INCREASE

CUTTING

DEPTH

START

ENGINE

STOP

START /

RUN

WIRES MUST BE

CONNECTED

DANGER

Depth Control Lever

START Position is the furthest

FORWARD position

Move lever REARWARD to increase

cutting depth

Summary of Contents for S-WLE-0799-F2N











































Search results

Summary of Contents for S-WLE-0799-F2N

Reviews:

Related manuals for S-WLE-0799-F2N

Brands by name

Popular brands

Southland S-WLE-0799-F2N, Operator'S Manual

Search results

Summary of Contents for S-WLE-0799-F2N

Reviews:

Related manuals for S-WLE-0799-F2N

Brands by name

Popular brands