Southbend SB1039F insert Manual Insert Download

Page: 29 / 136

For Machines Mfg. Since 5/11

14" TURN-X

Toolroom Lathe

-23-

P R E P A R A T I O N

Raise the lathe a couple of inches and check

the balance of the load.

— If the load is not safely balanced,

immediately lower the lathe and resolve

the issue before attempting to lift it

again.

Raise the lathe enough to clear the shipping

pallet, carefully remove the pallet, then

lower the lathe into position.

Leveling & Mounting

You must level your machine and either use

the included foot pads and leveling hardware or

bolt and shim your lathe to the floor. Because

mounting your lathe to the floor with permanent

hardware is an optional step and floor materials

may vary, floor mounting hardware is not

included.

Leveling

Leveling machinery helps precision components,

such as bedways, remain straight and flat during

the lifespan of the machine. Components on a

machine that is not level may slowly twist due to

the dynamic loads placed on the machine during

operation.

For best results, use a precision level that

is at least 12" long and sensitive enough to

show a distinct movement when a 0.003" shim

(approximately the thickness of one sheet of

standard newspaper) is placed under one end of

the level.

See the figure below for an example of a high

precision level.

Figure 17. Example of a precision level.

For accurate turning results and to prevent

warping the cast iron bed and ways, the lathe

bedways MUST be leveled from side-to-side

and from front-to-back on both ends.

Re-check the bedways 24 hours after

installation, two weeks after that, and then

annually to make sure they remain level.

When lifting the lathe with straps, the load

will be top heavy. Take extra care to keep the

load balanced vertically and only lift the lathe

far enough to remove the shipping pallet.

Attach the lifting straps to the power lifting

equipment (see Figure 16 for an example).

Figure 16. Example of lathe setup for lifting.

Power Lifting

Equipment

Lifting

Straps

Use Blocks as Necessary

to Space Straps Away

from Control Rod,

Feed Rod, and Leadscrew

to Prevent Bending when

the Lathe is Lifted

Hardwood

Blocking

Hardwood

Blocking

At each end of the lathe, have assistants

connect guide rods to safely keep the lathe

from swaying or tipping during lifting.

Summary of Contents for SB1039F insert









































































































































Search results

Summary of Contents for SB1039F insert

Reviews:

Related manuals for SB1039F insert

Brands by name

Popular brands

Southbend SB1039F insert, Manual Insert

Search results

Summary of Contents for SB1039F insert

Reviews:

Related manuals for SB1039F insert

Brands by name

Popular brands