background image

 

OWNER'S MANUAL 

INSTALLATION  

USER'S GUIDE 

GAS TILTING BRAISING PANS 

MODELS BGLT-24 BGLT-30 & BGLT-40 

These instructions should be read thoroughly before attempting installation. Set up, 
installation and Performance Check should be performed by a qualified service 
technician. The Manufacturer, Southbend (1100 Old Honeycutt Rd.,Fuquay-Varina, 
North Carolina 27526), informs you that unless the installation instructions for the 
above described Southbend product are followed and performed by a qualified 
service technician, (a person experienced in and knowledgeable concerning the 
installation of commercial gas and/or electrical cooking equipment) then the terms 
and conditions of the Manufacturer's Limited Warranty will be rendered void and no 
warranty of any kind shall apply. 

If the equipment has been changed, altered, modified or repaired by other than a 
qualified service technician during or after the 12-month limited warranty period, 
then the manufacturer shall not be liable for any incidental or consequential 
damages to any person or to any property which may result from the use of the 
equipment thereafter. Some States do not allow the exclusion or limitation of 
incidental or consequential damages, so the above limitation or exclusion thereto 
may not apply to you. 

In the event you have any question concerning the installation, use, care. or service 
of the product, write Customer Service Department, Southbend Corporation. 1100 Old 
Honeycutt Rd.. Fuquay-Varina, North Carolina 27526. 

 

Summary of Contents for BGLT-24








Reviews: