background image

 

TO: ALL SOUTHBEND SERVICE REPRESENTATIVES AND PARTS DISTRIBUTORS 

SUBJECT: INFRA RED BROILER - BROILER BURNER ORIFICE SIZING  

Please insert m your master manual - BR Broiler- Cheese Melter Section. 

Correct Infra Red Broiler Manual (170, 171D, 270) Part #1163089/1  
Revised 5-89 

Section 1 - Page 1 

Rate                    Orifice Size 

                                                              B.T.U.S. Hr -                 
Natural Gas                                           26.000                #41 

(.0960) 

Propane Gas                                          26.000                #53 

(.0595) 

Section 4 - Page 1 

Delete the following: 

1163554              Burner orifice assembly - Natural                               
1163586              Burner orifice assembly - Propane                              
1164370              Orifice spud - Natural No.36                                        
1166784              Orifice spud - Propane No. 51 

Add the following: 

For Suffix "D” 
1172601              Burner orifice (Natural) #41 
1172602              Burner orifice elbow 
1163653              Burner orifice (Propane) #53 
 For Suffix "A" 
1117497              Orifice fitting (Natural) 
1117499              Orifice fitting (Propane) 

1100 Old Honeycutt Rd.  
Fuquay-Varina, NC 27526  
(919) 552-9161  
FAX (919) 552-9798 

Summary of Contents for 171-40A





























Reviews: