manualshive.com logo in svg

Source Technologies Secure MICR, User Manual, Page: 39 / 66

Share
Download
Source Technologies Secure MICR User Manual Download Page 39

 

This command identifies the data to be printed in the first column of the report. It allows 
for a maximum of 14 characters in length. If less than 14 characters are sent, the printer 
fills the field with spaces when the audit report is printed. This field is only recorded in 
the audit report; it is not printed on the check. 
 

Audit Report Field Two-MICR Line &%SMDd..d$ or &%SM7d..d$

 

&%SMD or &%SM7 

 

 

Lead in sequence 

d..d 

 

 

Data to be printed 

$ 

 

 

Command terminator 

 
This command identifies the data to be printed in the second column of the report. It 
allows for a maximum of 40 characters in length. 
 

Audit Report Field Three 

&%SQ3d..d$

 

&%SQ3 

Lead in sequence  

d..d 

Data to be printed 

$ 

Command terminator 

 
This command identifies the data to be printed in the third column of the report. It allows 
for a maximum of 40 characters. 
 

Audit Report Field Four 

&%SQ4d..d~

 

&%SQ4 

Lead in sequence 

d..d 

Data to be printed 

~ 

Command terminator 

 
This command identifies the data to be printed in the fourth column of the report. It 
allows for a maximum of 16 characters in length. Since a total of this field can be 
provided at the end of the Audit Trail Report it is typically used for the convenience 
amount field.   
 

Note:

 This is the only command where the $ is not a command terminator. The 

tilde ~ (hex 7E) acts as the command terminator. 
 

Audit Report Field Five 

&%SQ5d..d$

 

&%SQ5 

Lead in sequence 

d..d 

Data to be printed 

$ 

Command terminator 

 
This command identifies the data to be printed in the fifth column of the report.  This field 
allows for a maximum of eight characters.   

Audit Report Field Six 

&%SQ6d..d$

 

&%SQ6 

Lead in string 

Audit Trail Reports  |  7 

 

 

Source Technologies, LLC                                                             ST9720 Secure MICR Printer User’s Guide 

 

 

35 

Summary of Contents for Secure MICR



































































Reviews:

No comments