Soundigital 3000.1 EVO 5 1 Owner'S Manual Download Page 9

9

Ø

Mount the amplifier in such a way you have access to the connectors;

Ø

Install the power cables in the vehicle properly, starting from the battery to the fuse 
holder  or  circuit  breaker,  use  the  cable  with  the  appropriate  size.  Make  all 
connections, install fuse holders or circuit breakers, but without placing the fuses 
or with the circuit breakers in the "OFF" position;

Ø

Connect the power cables in to the amplifier, observing the polarity. Connect all the 
positive cables from the fuse holder or circuit breaker to the positive conector of 
the amplifier and all the negative power cables from the batteries to the negative 
connector of the amplifier;

Ø

The  ground  cable  must  be  as  short  as  possible  and  must  be  connected  to  the 
vehicle chassis and the battery negative;

Ø

Install the signal input cables in a proper way, distant from the power cables;

Ø

Connect  the  RCA  or  the  high  level  signal  input  cables  to  the  head  unit  and 
amplifiers;

Ø

Install the audio output cables with the appropriate section, distant from the power 
and audio input cables;

Ø

Connect  the  audio  output  cables  to  the  amplifier  and  speakers  respecting  the 
positive (+) and negative (-) polarities;

Ø

Install the remote cable with the power cables, using 1.5mm² (15 AWG) cable or 
thicker;

Ø

Connect the remote power cable to the amplifier's "REM" terminal at the main unit's 
remote power output (when not using the high level signal inputs);

Ø

Before powering the system, verify all the connections and make sure there are no 
mistakes or short-circuits on the power and ground cables;

Ø

;

Reconnect the ground of the batteries

Ø

Check if the head unit is turned off and then place the fuses in the fuse holders or 
switch the circuit breakers on;

Ø

Turn on the main unit and the amplifier will turn on the "ON" LED indicating that it is 
in operation.

INSTALLATION SEQUENCE

Warning!

Warning!

Remove the paint between
the terminal and chassis

THE  MAXIMUM  DISTANCE  FOR  THE  INSTALLATION  OF  THE  FUSE/CIRCUIT 
BREAKER IS 12 INCHES (30cm) AWAY FROM THE BATTERY.

Summary of Contents for 3000.1 EVO 5 1















Reviews: