background image

22

USER GUIDE

USER GUIDE

USER GUIDE

USER GUIDE

USER GUIDE

8

 PLAYBACK TO MIX

Press this switch to route the Playback in signals, connected to the Left and Right
RCA sockets 

7

, to the MIX Left/Right signal at the MIX outputs.

9

 MONITOR PLAYBACK

Press this switch to route the Playback signal to the monitor and phones, over-
riding the default Monitor/Phones signal.

0

 MONITOR LEVEL

This control sets the level to the MONITOR LEFT & RIGHT outputs.  If headphones
are plugged into the PHONES jack, the headphone level will track the Monitor
Level.

q

 MONITOR OUTPUTS

The Monitor Outputs are on 3-pole ‘A’ gauge jacks and are balanced connections

w

 PHONES LEVEL

This control sets the output level to the Headphone outputs.  If headphones are
plugged into the PHONES jack, then the knob sets a comfortable headphone
listening level without affecting the Monitor output levels.

e

 HEADPHONES JACK

The PHONES output is a 3-pole ‘A’ gauge jack, wired as a stereo output as
shown, ideally for headphones of 200

 or greater.  8

 headphones are not

recommended.

r

 AUX OUTPUTS (1 & 2)

These outputs are on 3-pole ‘A’ gauge jacks and are balanced outputs.

t

 AUX PRE/POST  SWITCHES

These two switches globally switch the AUX 1 and AUX 2 feeds, respectively, on
all the input modules to be either pre-fade or post-fade.

7

1

2

3

4

5

6

8

9

0

q

w

e

r

t

Summary of Contents for Spirit E series











































Reviews: