background image

www.soundskulptor.com

Document revision 1.1 – Last modification : 27/05/21

EQ573-II Assembly guide

Safety warning

The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the 

realisation of a kit unless he has full knowledge about safely handling main powered devices.

Please read the “DIY guide” before beginning.

Print or open the following documents :

EQ573-II Schematics

EQ573-II Components layout

EQ573-II Parts list

Follow this guide from item number 1 till the end, in this order. The assembly order is based on components height, from

low to high profile, in order to ease the soldering process : The component you are soldering is always taller than the 
previously assembled ones and it is pressing nicely against the work area foam.

Soldering

All the PCB holes are metallized. It means the connection between the top and bottom pads is already 
done. The parts must be soldered only from below (unless differently stated).
Use only small diameter solder, 0.5 or 0.7 mm, 1mm maximum. Use the minimum possible amount of 
solder. Bad joints are almost always caused by too much solder.
Cut the component leads and pins totally flush with the PCB after soldering. A too long tail could create 
an electric connection with the side plate.
Here are two excellent introduction to soldering videos:

http://www.eevblog.com/2011/06/19/eevblog-180-soldering-tutorial-part-1-tools/

http://www.eevblog.com/2011/07/02/eevblog-183-soldering-tutorial-part-2/

 

EQ573-II Assembly guide – Main board

1. PCB split

Split the PCB into 4 parts along the grooves.

Use extra thin sandpaper to polish all the rough
sides.

Copyright ©2020 to today SoundSkulptor

Summary of Contents for EQ573-II












Reviews: