Soucy PUMA 115 User Manual Download

Page: 53 / 154

5.3

NOTICE

WHEN APPLICABLE, GREASE THE TRACK SYSTEM AT INSTALLATION. WHEN GREASING
AXLES, ENSURE THAT GREASE SPILLS OUT FROM BOTH ENDS OF AXLE.

•

Paint mark bolts for quick visual inspection.

•

Remove paint from contact surfaces on vehicle axle housings, track system attachments, and frames. This will
prevent hardware loosening that can result in broken components and injuries.

•

Use anti-seize compound with bolts secured in the tractor structure.

•

Before proceeding with the installation of your system, arrange parts per their assembly sequence.

•

The tractor may be seated on track system frames (rubber track removed).

NOTICE

SOUCY TRACK HIGHLY RECOMMENDS USING THREAD LOCK ON BOLTS, PARTICULARLY
FOR BOLTS WITHOUT LOCKING DEVICES

SOUCY TRACK SYSTEMS USER GUIDE

A-8C0214-3-EN

Summary of Contents for PUMA 115



























































































































































Search results

Summary of Contents for PUMA 115

Reviews:

Related manuals for PUMA 115

Brands by name

Popular brands

Soucy PUMA 115, User Manual

Search results

Summary of Contents for PUMA 115

Reviews:

Related manuals for PUMA 115

Brands by name

Popular brands