SOREX FLEX Fingerprint, User Manual

Page: 13 / 20

SOREX
wireless Solutions GmbH
Technologie- und Forschungszentrum
Viktor-Kaplan-Straße 2,B
2700 Wiener Neustadt, Österreich
UID ATU57865279
Bank Raiffeisenbank Pittental
IBAN AT223264700000052324
BIC RLNWATW1647
T +43 2622 320130
F +43 2622 3201315
@
w³
www.sorex-schliesssystem.com
SOREX
wireless Solutions GmbH
Technologie- und Forschungszentrum
Viktor-Kaplan-Straße 2,B
2700 Wiener Neustadt, Österreich
UID ATU57865279
Bank Raiffeisenbank Pittental
IBAN AT223264700000052324
BIC RLNWATW1647
T +43 2622 320130
F +43 2622 3201315
@
w³
www.sorex-schliesssystem.com
English
10
Operation
Note: In delivery condition, the cylinder can be opened by every
finger or remote control. Only after teaching in an administrator
finger, triggering an opening action is limited to authorised fingers
or remote controls.
Note: The buttons „Set“ and „Reset“ have to be pressed by using the
supplied needle.
Note: Before the fingerprint sensor can be used, the button
has to be pressed. However, this does not apply to the settings with
“Set”.
1. Add administrator finger

Press “Set” twice or until “Add Admin FP” is shown and wait ~5
seconds.
 Put your finger three times on the fingerprint sensor.
There can be up to 3 administrator fingers at the same time. All
following fingers after the first administrator finger, have to be
acknowledged by the first one.
Note: If you taught in an administrator finger, you have to place the
administrator finger on the fingerprint sensor for all operations.
2. Add user finger
 Press “Set” three times or until “Add User FP” is shown and
wait ~5 seconds.

Place administrator finger

Put the user finger three times on the fingerprint sensor.
 Please make a note of the ID of the currently added finger. This
ID is of help if you want to delete this finger.
3. Delete user finger

Press “Set” four times or until “Delete Single FP” is shown and
wait ~5 seconds.
 Place administrator finger
 Use “Set” to select the user who is going to be deleted. Confirm
by pressing
. After 2 seconds of idling, the cylinder exits
the delete user mode and returns to standard operation.
4. Delete all user finger
 Press “Set” five times or until “Clear all User FPs” is shown and
wait ~5 seconds.

Place administrator finger
5. Add remote control
 Press “Set” six times or until “Add Remote” is shown and wait
~5 seconds.

Place administrator finger
 Press a button on the remote control within 60 seconds.
There can be up to 8 remote controls at the same time.
6. Delete all remote controls

Press „Set” seven times or until “Clear all Remote” is shown
and wait ~5 seconds.
 Place administrator finger
7. Add a main RC

This is an extension that has not been published yet. Please do
not use this option.
8. Delete the main RC

This is an extension that has not been published yet. Please do
not use this option.
9. Language settings

Press “Set” ten times or until Chinese text is shown and wait
~5 seconds.

Place administrator finger
10. Lock Time settings

Press “Set” eleven times or until “Set Lock Time” is shown and
wait ~5 seconds.

Place administrator finger
 Press “Set” button to alter the lock time in 1-second
increments.

You can set the time to a minimum of five and a maximum of
14 seconds.
In delivery condition, the lock time is configured to 8 seconds.
11. Turn on Bluetooth

This feature is not supported due to security reasons. Please
do not use this option.
12. Reset cylinder to delivery condition
 Press “Set” thirteen times or until “Restore to Init State” is
shown and wait ~5 seconds.

Place administrator finger
All previously taught in remote controls, administrator-, and user
fingers have been deleted now.
13. Firmware and Hardware

Press “Set” fourteen times or until “PCBA VER FW VER” is
shown and wait ~5 seconds.
Here you can see some information about the firmware and
hardware.
14. Aging Test

Press “Set” fifteen times or until “Aging Test” is shown and
wait ~5 seconds.
This option executes a test to determine how much battery power
is consumed by every opening or locking procedure.
This test does not stop on its own and must be aborted by using the
“Reset” button (The button on the other side of the “Set” button).
Note: You can only execute an aging test if there is no admin finger.