background image

(4) About the Remote Control

4.1 Pull out the insulating sheet, you can use the remote control directly.
4.2 The remote control can directly control the treadmill.
4.3 If you have purchased multiple treadmills, in order to prevent the treadmills from

interfering with each other, please perform the following operations to match.

4.3.1 Turn on the treadmill.
4.3.2 Simultaneously press the left and right buttons on the remote control for 5 seconds.

The display will flash, and the treadmill and the remote control will be paired.

4.3.3 Please note: After matching the remote control, if the remote control isreplaced,

please perform the matching again according to the above operation.

6. Bluetooth Speaker Instructions

Turn on the Bluetooth switch in the phone settings, find the available Bluetooth devices in the
Bluetooth device connection selection, then select and connect the available Bluetooth audio
devices.

7. USAGE OF SILICONE OIL

Pull up tightly of the running belt. Then put the silicone oil to
running board. Then start the machine to running 3 minutes
without loading. It is better to maintain like this every 30 hours
working of the machine. This can save lifetime of parts properly.

Summary of Contents for A90-326V80









Reviews: