manualshive.com logo in svg

Sony XDCAM PDW-HR1, Operation Manual, Page: 41 / 214

Share
Download
Sony XDCAM PDW-HR1 Operation Manual Download Page 41

41

Preparing Power Sources

Chapter

  Chapt

er

 3

  Pre

par

at

ion
s

3

Preparations

Preparing Power Sources

This unit can be powered by AC power, DC power, or a 
battery pack.
For safety, use only the Sony battery packs listed below.
Lithium-ion battery pack: BP-L80S, BP-GL95

If you load or remove a battery pack incorrectly, it may fall 
and cause bodily injury. Follow the procedures described 
below to load or remove them.

Supplying power

AC power supply

Connect the AC IN connector to an AC power source using 
the specified AC power cord. To supply AC power to the 
unit, set the on/standby switch on the control panel to 

=

 

(ON) and the POWER switch on the connector panel to 

=

 

(ON).

DC power supply

Connect the DC IN 12V connector to a DC power source.
To supply DC power to the unit, set the on/standby switch 
on the control panel to 

=

 (ON) and the POWER switch on 

the connector panel to OFF. If the POWER switch on the 
connector panel is set to 

=

 (ON), AC power is supplied.

Battery power supply

Battery packs that can be used with this unit are as follows.
• BP-L80S
• BP-GL95

Continuous recording time at room temperature

BP-GL95 lithium-ion battery pack: 95 minutes

For details on charging battery packs, refer to the 
operation manual for the battery charger.

Notes about battery usage

• Before using the batteries, be sure to charge them fully 

with the special battery charger. Refer to the operating 
instructions for your battery charger for more 
information about how to charge the batteries.

• Batteries may not be completely charged if you charge 

them immediately after use when they are still warm. 
You should wait until the batteries cool before charging 
them.

Attaching a battery pack

Proceed as follows.

1

Remove the cover of the battery pack shoe.

2

Fit the battery pack.

Note

2

1

Summary of Contents for XDCAM PDW-HR1























































































































































































































Reviews:

No comments